Production of Green Synthesized Zinc Oxide Nanoparticle-Reinforced PMMA-Based Photopolymer Resins on DLP-Based 3D Printers and Characterization
Polymers · 18.05.2026 · 18 (10) · 1229
DOI: 10.3390/polym18101229 ↗Kurz gefasst
Fachartikel in der Zeitschrift Polymers, online erschienen am 18.05.2026. Verfasst von Behiç Selman Erdoğdu und 4 weiteren Autor:innen. Beteiligte Einrichtung: Department of Molecular Biology and Genetics, Faculty of Science, Necmettin Erbakan University, Konya 42090, Türkiye. Die Arbeit wurde bisher 4-mal zitiert (Crossref) und nennt 46 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Necmettin Erbakan University Scientific Research Projects Coordination Office (BAP).
Abstract (Originalsprache)
In this study, the structural, thermal, and mechanical properties of nanocomposites obtained by adding zinc oxide (ZnO) nanoparticles (NPs), produced by phyto-mediated synthesis using Dianthus chinensis plant extract, to a PMMA-based photopolymer resin at different ratios (0.05%, 0.10%, 0.15%, 0.20%, and 0.25%, by weight) were evaluated. The prepared composite resins were produced in different test geometries using a DLP (digital light processing)-based 3D printer (Asiga Ultra). Following the structural characterization of ZnO nanoparticles, tensile, compressive, and flexural mechanical tests were performed on the resulting composites, as well as FTIR, TGA, DSC, and DMA analyses. The FTIR results showed that ZnO NPs were physically integrated into the matrix. TGA and DSC analyses revealed that the addition of ZnO NPs, particularly at an addition rate of 0.15%, increased thermal stability. DMA analyses showed an increase in storage modulus and glass transition temperature as the addition rate increased. In mechanical tests, the highest modulus of elasticity and maximum strength values were obtained at additive ratios of 0.10–0.15%. The highest tensile strength (55.31 MPa) and compressive strength (388.53 MPa) were obtained at ZnO contents of 0.10–0.15 wt%, while the maximum flexural strength reached 125.94 MPa at 0.15 wt% ZnO. In addition, the storage modulus increased from 1.469 × 109 Pa for the control resin to 1.872 × 109 Pa for the composite containing 0.15 wt% ZnO, indicating improved stiffness and thermomechanical stability. The stress–strain curves show that improvements in ductility and deformation capacity of the material are achieved at these additive ratios. The findings demonstrate that green-synthesized ZnO nanoparticles are an effective and sustainable additive material for improving the mechanical and thermal performance of DLP-based photopolymer dental resins.
Schlagwörter
Stichwörter der Autor:innen
Autor:innen und Institutionen
- Department of Molecular Biology and Genetics, Faculty of Science, Necmettin Erbakan University, Konya 42090, Türkiye.
- Department of Metallurgy and Material Engineering, Faculty of Engineering, Necmettin Erbakan University, Konya 42090, Türkiye.
- Science and Technology Research and Application Center (BITAM), Necmettin Erbakan University, Konya 42090, Türkiye.
- Department of Civil Engineering, Necmettin Erbakan University, Konya 42090, Türkiye.
- Department of Technical Sciences, Western Caspian University, Baku 1001, Azerbaijan.
- Department of Biotechnology, Graduate School of Natural and Applied Sciences, Necmettin Erbakan University, Konya 42090, Türkiye.
ORCID-Profile: Behiç Selman Erdoğdu, Muhammed İhsan Özgün, Emrah Madenci, Mehmet Ali Sayınbatur, Fatih Erci
Förderung
- Necmettin Erbakan University Scientific Research Projects Coordination Office (BAP)
Zitieren
APA
Erdoğdu, B. S., Özgün, M. İ., Madenci, E., Sayınbatur, M. A., & Erci, F. (2026). Production of Green Synthesized Zinc Oxide Nanoparticle-Reinforced PMMA-Based Photopolymer Resins on DLP-Based 3D Printers and Characterization. Polymers, 18(10), 1229. https://doi.org/10.3390/polym18101229
Vancouver
Erdoğdu BS, Özgün Mİ, Madenci E, Sayınbatur MA, Erci F. Production of Green Synthesized Zinc Oxide Nanoparticle-Reinforced PMMA-Based Photopolymer Resins on DLP-Based 3D Printers and Characterization. Polymers. 2026;18(10):1229. doi:10.3390/polym18101229
BibTeX
@article{Erdodu2026,
author = {Erdoğdu, Behiç Selman and Özgün, Muhammed İhsan and Madenci, Emrah and Sayınbatur, Mehmet Ali and Erci, Fatih},
title = {Production of Green Synthesized Zinc Oxide Nanoparticle-Reinforced PMMA-Based Photopolymer Resins on DLP-Based 3D Printers and Characterization},
journal = {Polymers},
year = {2026},
volume = {18},
number = {10},
pages = {1229},
doi = {10.3390/polym18101229}
}
EUVIMED