EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Towards Qualification of Epoxy Resins for Superconducting Magnets Exposed to Radiation Doses Exceeding 100 MGy: Effect of the Radiation Source and Environment

Christian Scheuerlein iD, Federico Ravotti iD, Giuseppe Pezzulo, Torsten Koettig, Oliver Aberle, Ana-Paula Bernardes, Roland Piccin iD, Michael Eisterer iD

Polymers · 29.04.2026 · 18 (9) · 1079

DOI: 10.3390/polym18091079 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Polymers, online erschienen am 29.04.2026. Verfasst von Christian Scheuerlein und 7 weiteren Autor:innen. Beteiligte Einrichtung: European Organization for Nuclear Research (CERN), Esplanade des Particules 1, 1211 Geneva, Switzerland. Die Arbeit wurde bisher 2-mal zitiert (Crossref) und nennt 61 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

To qualify epoxy resin systems for use in superconducting magnets of future particle accelerators up to peak doses beyond 100 MGy, the effects of the irradiation source, the irradiation environment and the irradiation temperature have been assessed. Identical epoxy resin samples have been irradiated with 60Co gamma rays, 24 GeV/c protons and by mixed neutron/gamma radiation in a reactor and at a spallation source up to a dose of 170 MGy. Irradiation-induced cross-linking and chain scission have been monitored by Dynamical Mechanical Analysis (DMA). When irradiations are performed with the same dose rate and in the same environment, the different radiation sources have a similar efficiency to produce radiation damage, and the total absorbed dose is a good scaling factor to compare irradiation effects in polymers. To distinguish between the influence of the irradiation temperature and of environmental oxygen, proton irradiations have been carried out in ambient air, inert gas at ambient temperature and in liquid helium. Compared to ambient air irradiation, in inert atmosphere more cross-linking is observed. Cross-linking rates are strongly reduced at 4.2 K. For some polymers the irradiation temperature has a strong influence on the chain scission rate. The most-radiation-hard epoxy resin systems maintain substantial mechanical strength up to doses beyond 100 MGy.

Schlagwörter

Stichwörter der Autor:innen

DMAFCCHL-LHCchain scissioncross-linkingepoxy resingamma irradiationmuon colliderneutron irradiationproton irradiationsuperconducting magnettotal absorbed dose

Autor:innen und Institutionen

  • European Organization for Nuclear Research (CERN), Esplanade des Particules 1, 1211 Geneva, Switzerland.
  • Atominstitut, TU Wien, Stadionallee 2, 1020 Vienna, Austria.

ORCID-Profile: Christian Scheuerlein, Federico Ravotti, Roland Piccin, Michael Eisterer

Zitieren

APA

Scheuerlein, C., Ravotti, F., Pezzulo, G., Koettig, T., Aberle, O., Bernardes, A. P., Piccin, R., & Eisterer, M. (2026). Towards Qualification of Epoxy Resins for Superconducting Magnets Exposed to Radiation Doses Exceeding 100 MGy: Effect of the Radiation Source and Environment. Polymers, 18(9), 1079. https://doi.org/10.3390/polym18091079

Vancouver

Scheuerlein C, Ravotti F, Pezzulo G, Koettig T, Aberle O, Bernardes AP, et al. Towards Qualification of Epoxy Resins for Superconducting Magnets Exposed to Radiation Doses Exceeding 100 MGy: Effect of the Radiation Source and Environment. Polymers. 2026;18(9):1079. doi:10.3390/polym18091079

BibTeX
@article{Scheuerlein2026,
  author = {Scheuerlein, Christian and Ravotti, Federico and Pezzulo, Giuseppe and Koettig, Torsten and Aberle, Oliver and Bernardes, Ana-Paula and Piccin, Roland and Eisterer, Michael},
  title = {Towards Qualification of Epoxy Resins for Superconducting Magnets Exposed to Radiation Doses Exceeding 100 MGy: Effect of the Radiation Source and Environment},
  journal = {Polymers},
  year = {2026},
  volume = {18},
  number = {9},
  pages = {1079},
  doi = {10.3390/polym18091079}
}
Kostenlos starten →