Evaluation of Shear Performance of Integrated GFRP Stirrup Systems in Reinforced Concrete Beams
Polymers · 09.04.2026 · 18 (8) · 921
DOI: 10.3390/polym18080921 ↗Kurz gefasst
Fachartikel in der Zeitschrift Polymers, online erschienen am 09.04.2026. Verfasst von Saruhan Kartal und 5 weiteren Autor:innen. Beteiligte Einrichtung: Department of Civil Engineering, Faculty of Engineering and Natural Sciences, Kirikkale University, Kirikkale 71451, Turkey. Die Arbeit nennt 30 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).
Abstract (Originalsprache)
This study investigates the shear behavior of glass fiber-reinforced polymer (GFRP)-reinforced concrete (RC) beams to address challenges associated with their low elastic modulus, absence of yielding, and reduced stirrup efficiency in bending regions. GFRP bars are increasingly adopted as an alternative to steel due to their superior corrosion resistance, durability, and cost-effectiveness. This study focuses on the effects of stirrup type, stirrup spacing, and shear span-to-effective depth ratio on the structural performance of GFRP RC beams. Twelve full-scale beams were tested under four-point bending, incorporating three GFRP shear reinforcement configurations: fabricated closed stirrups, integrated straight bar systems, and discrete vertical bars. Experimental observations were analyzed in terms of failure modes, load-carrying capacity, energy absorption, and deformation characteristics. Results indicate that fabricated F-type stirrups provide the highest shear performance, though their effectiveness is limited by premature rupture at bending points. Site-integrated S- and T-type configurations offer practical alternatives, maintaining structural integrity while mitigating bend-related stress concentrations, but with slightly lower energy absorption and load capacity. Increasing stirrup spacing significantly reduces shear resistance and shifts failure from flexural to shear-dominated modes. Comparisons with widely used design codes and analytical models show that CSA S806-12 provisions offer the most reliable predictions, while other guidelines tend to over- or underestimate shear capacity depending on configuration and a/d ratio. The study highlights the importance of optimizing stirrup type and spacing to enhance the shear performance of GFRP RC beams. Findings provide valuable insights for improving current design methodologies, offering guidance for engineers seeking durable, corrosion-resistant alternatives to steel reinforcement in aggressive environments. This research demonstrates that innovative site-integrated stirrup configurations can bridge practical fabrication constraints without compromising overall shear performance, promoting more efficient and resilient GFRP RC structures.
Schlagwörter
Stichwörter der Autor:innen
Autor:innen und Institutionen
- Department of Civil Engineering, Faculty of Engineering and Natural Sciences, Kirikkale University, Kirikkale 71451, Turkey.
- Institute of Science, Kirikkale University, Kirikkale 71451, Turkey.
- Department of Civil Engineering, Faculty of Engineering, University of Tabuk, Tabuk 71491, Saudi Arabia.
- Department of Civil Engineering, Engineering Faculty, Karamanoglu Mehmetbey University, Karaman 70200, Turkey.
ORCID-Profile: İlker Kalkan, Turki S Alahmari, Abderrahim Lakhouit, Akin Duvan
Zitieren
APA
Kartal, S., Gündoğan, U., Kalkan, İ., Alahmari, T. S., Lakhouit, A., & Duvan, A. (2026). Evaluation of Shear Performance of Integrated GFRP Stirrup Systems in Reinforced Concrete Beams. Polymers, 18(8), 921. https://doi.org/10.3390/polym18080921
Vancouver
Kartal S, Gündoğan U, Kalkan İ, Alahmari TS, Lakhouit A, Duvan A. Evaluation of Shear Performance of Integrated GFRP Stirrup Systems in Reinforced Concrete Beams. Polymers. 2026;18(8):921. doi:10.3390/polym18080921
BibTeX
@article{Kartal2026,
author = {Kartal, Saruhan and Gündoğan, Uğur and Kalkan, İlker and Alahmari, Turki S and Lakhouit, Abderrahim and Duvan, Akin},
title = {Evaluation of Shear Performance of Integrated GFRP Stirrup Systems in Reinforced Concrete Beams},
journal = {Polymers},
year = {2026},
volume = {18},
number = {8},
pages = {921},
doi = {10.3390/polym18080921}
}
EUVIMED