EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Hollow Auxetic Polymer Structures with Manufacturing-Constrained Design and Mechanical Validation

Finlay Bridge, Rakan Albarakati iD, Hany Hassanin iD, Khamis Essa iD

Polymers · 28.03.2026 · 18 (7) · 828

DOI: 10.3390/polym18070828 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Polymers, online erschienen am 28.03.2026. Verfasst von Finlay Bridge und 3 weiteren Autor:innen. Beteiligte Einrichtung: Mechanical Engineering, University of Birmingham, Edgbaston, Birmingham B15 2TT, UK. Die Arbeit wurde bisher 1-mal zitiert (Crossref) und nennt 45 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Umm Al-Qura University, Umm Al-Qura University https://ror.org/01xjqrm90.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Hollow auxetic structures enable lightweight mechanical design by reducing mass while preserving architected deformation. However, hollow auxetic studies focus on LPBF metals. This study presents a manufacturing-constrained design and validation framework for a hollow hybrid re-entrant chiral lattice produced by stereolithography. The unit cell was parameterised by chiral angle, re-entrant strut length, and hollow internal diameter, with drainage features integrated into the CAD model to preserve hollow channels during printing and post-processing. A minimum internal diameter study defined the printable design window. Within these limits, a central composite design coupled with finite element analysis mapped the response surface and identified an optimised geometry of θ = 15°, L = 3.5 mm, and d = 1.68 mm, with a predicted unit-cell negative Poisson’s ratio of about −1.17. Compression testing confirmed that the printed unit cell and 3 × 3 × 3 lattice retained the intended rotation-dominated auxetic deformation mode. At the selected comparison strain, the unit cell showed a negative Poisson’s ratio of −0.68 and the 3 × 3 × 3 lattice showed −0.29. Relative to the solid lattice, the hollow lattice reduced density by 42.4% with only a 3.0% reduction in stiffness, increasing specific stiffness by 68.9% and specific peak strength by 5.2%, but reducing specific energy absorption by 25.6% due to earlier localisation and junction driven fracture. These results provide practical design guidance for manufacturable hollow SLA auxetic lattices, especially for lightweight and stiffness-limited applications where low mass and high specific stiffness are more important than energy absorption.

Schlagwörter

Stichwörter der Autor:innen

Poisson’s ratioauxetic metamaterialdesign of experimentshollow strutstereolithography

Autor:innen und Institutionen

  • Mechanical Engineering, University of Birmingham, Edgbaston, Birmingham B15 2TT, UK.
  • Industrial Engineering Department, College of Engineering and Architecture, Umm Al-Qura University, Makkah 21955, Saudi Arabia.
  • School of Sciences, Psychology, Arts and Humanities, Computing, Engineering, and Sport, Canterbury Christ Church University, Canterbury CT1 1QU, UK.

ORCID-Profile: Rakan Albarakati, Hany Hassanin, Khamis Essa

Förderung

  • Umm Al-Qura University
  • Umm Al-Qura University https://ror.org/01xjqrm90

Zitieren

APA

Bridge, F., Albarakati, R., Hassanin, H., & Essa, K. (2026). Hollow Auxetic Polymer Structures with Manufacturing-Constrained Design and Mechanical Validation. Polymers, 18(7), 828. https://doi.org/10.3390/polym18070828

Vancouver

Bridge F, Albarakati R, Hassanin H, Essa K. Hollow Auxetic Polymer Structures with Manufacturing-Constrained Design and Mechanical Validation. Polymers. 2026;18(7):828. doi:10.3390/polym18070828

BibTeX
@article{Bridge2026,
  author = {Bridge, Finlay and Albarakati, Rakan and Hassanin, Hany and Essa, Khamis},
  title = {Hollow Auxetic Polymer Structures with Manufacturing-Constrained Design and Mechanical Validation},
  journal = {Polymers},
  year = {2026},
  volume = {18},
  number = {7},
  pages = {828},
  doi = {10.3390/polym18070828}
}
Kostenlos starten →