Comparative Experimental Assessment of Elastomeric and Thermoplastic Sealing Materials in Valve Sealing Under Cyclic High-Pressure Hydrogen Exposure
Polymers · 27.03.2026 · 18 (7) · 814
DOI: 10.3390/polym18070814 ↗Kurz gefasst
Fachartikel in der Zeitschrift Polymers, online erschienen am 27.03.2026. Verfasst von Enric Palau Forte und 1 weiteren Autor:innen. Beteiligte Einrichtung: Redfluid, 08227 Terrassa, Spain. Die Arbeit nennt 17 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Generalitat de Catalunya.
Abstract (Originalsprache)
Hydrogen is increasingly adopted as a clean energy carrier for storing and transporting low-carbon energy. Achieving a practical volumetric energy density for real-world deployment typically requires compression to several hundred bar, which in turn demands dedicated high-pressure infrastructure. Because valves are indispensable for isolation and flow control within this infrastructure, durable sealing valve materials become a key reliability and safety requirement. This assembly-level screening study compares two valve configurations with different polymer assemblies: EPDM O-rings with PEEK seats/bushing and NBR O-rings with POM seats/bushing. Four new identical 500-bar ball valves were tested (two EPDM/PEEK and two NBR/POM). For each seal configuration, one valve was cycled 5000 times at 500 bar in helium (inert baseline), and a second identical valve was cycled 5000 times at 500 bar in hydrogen to isolate hydrogen effects from mechanical/metallic wear. Leakage was tracked during cycling, and seals were analyzed by SEM/EDX after testing. The EPDM/PEEK configuration remained leak-tight in both gases, with no cracking observed in the elastomer or thermoplastic components. The NBR/POM configuration exhibited POM bushing fracture during cycling and minor external leakage at the stem during the hydrogen phase, accompanied by micro-fissures on the NBR O-ring surface. EDX indicated composition changes after cycling, including oxygen and fluorine enrichment and occasional metallic transfer species, consistent with surface films and deposits. Under the present valve geometry and cycling protocol, EPDM/PEEK provided robust sealing, whereas NBR/POM showed failure modes relevant to high-pressure service. These findings are intended as configuration-level screening evidence to be used in valves rather than as a full qualification of the individual materials.
Schlagwörter
Stichwörter der Autor:innen
Autor:innen und Institutionen
- Redfluid, 08227 Terrassa, Spain.
- Chemical Engineering Department, Universitat Rovira I Virgili, 43007 Tarragona, Spain.
ORCID-Profile: Enric Palau Forte, Francesc Medina Cabello
Förderung
- Generalitat de Catalunya
Zitieren
APA
Palau Forte, E., & Cabello, F. M. (2026). Comparative Experimental Assessment of Elastomeric and Thermoplastic Sealing Materials in Valve Sealing Under Cyclic High-Pressure Hydrogen Exposure. Polymers, 18(7), 814. https://doi.org/10.3390/polym18070814
Vancouver
Palau Forte E, Cabello FM. Comparative Experimental Assessment of Elastomeric and Thermoplastic Sealing Materials in Valve Sealing Under Cyclic High-Pressure Hydrogen Exposure. Polymers. 2026;18(7):814. doi:10.3390/polym18070814
BibTeX
@article{PalauForte2026,
author = {Palau Forte, Enric and Cabello, Francesc Medina},
title = {Comparative Experimental Assessment of Elastomeric and Thermoplastic Sealing Materials in Valve Sealing Under Cyclic High-Pressure Hydrogen Exposure},
journal = {Polymers},
year = {2026},
volume = {18},
number = {7},
pages = {814},
doi = {10.3390/polym18070814}
}
EUVIMED