EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Static and Cyclic Mechanical Behavior of 3D-Printed PEEK Under Tensile and Compressive Loads

Francisco Pina, Carlos M S Vicente, Joaquim Justino Netto iD, Luís Reis iD

Polymers · 19.03.2026 · 18 (6) · 748

DOI: 10.3390/polym18060748 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Polymers, online erschienen am 19.03.2026. Verfasst von Francisco Pina und 3 weiteren Autor:innen. Beteiligte Einrichtung: IST, Instituto Superior Técnico, Universidade de Lisboa, Av. Rovisco Pais, 1049-001 Lisbon, Portugal. Die Arbeit wurde bisher 4-mal zitiert (Crossref) und nennt 41 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Fundação para a Ciência e Tecnologia, Fundação para a Ciência e a Tecnologia, Research Unit of Centre for Mechanical and Aerospace Science and Technologies.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Polyether ether ketone (PEEK) is a high-performance polymer with exceptional mechanical properties, durability and lightweight. 3D printing of PEEK can be very beneficial in the medical industry to manufacture patient-specific implants; however, there is a lack of studies regarding the fatigue behavior of 3D-printed PEEK, especially under compression, which is closely related to its potential applications. This paper investigates the static and dynamic mechanical performance of 3D-printed PEEK. Tensile and compression tests were conducted on specimens with ±45° raster orientation. Annealing at 270 °C for 5 h increased crystallinity from 34.4% to 41.4% yet unexpectedly reduced tensile strength from 60.8 MPa to 47.3 MPa, while increasing Young’s modulus from 2.51 GPa to 3.51 GPa. Micro-CT analysis revealed increased pore size after annealing. Static compression strength showed improvement post-annealing, increasing from 80.1 MPa to 126.7 MPa, with modulus rising from 1.64 GPa to 2.28 GPa. Compression–compression fatigue tests, performed at 5 Hz and 2.5 Hz with stress amplitudes of 70–95% of maximum strength (R = 0.1), enabled the construction of the first S-N curve for 3D-printed PEEK under compressive loading. Annealed specimens exhibited superior fatigue life, with infinite life achieved at 83.3 MPa (70% of static strength). Thermal imaging highlighted the role of temperature in fatigue failure, showing that annealed specimens endured higher thermal loads. These findings support the suitability of 3D-printed PEEK for load-bearing biomedical applications under cyclic compressive loads.

Schlagwörter

Stichwörter der Autor:innen

3D printingannealingcompression fatiguemechanical characterizationpolyether ether ketone (PEEK)

Autor:innen und Institutionen

  • IST, Instituto Superior Técnico, Universidade de Lisboa, Av. Rovisco Pais, 1049-001 Lisbon, Portugal.
  • Atlântica-Instituto Universitário, Fábrica de Pólvora de Barcarena, 2730-036 Barcarena, Portugal.
  • Center for Mechanical and Aerospace Science and Technologies (C-MAST-UBI), University da Beira Interior, R. Marquês de D'Ávila e Bolama, 6201-001 Covilhã, Portugal.
  • IDMEC, Instituto Superior Técnico, Universidade de Lisboa, Av. Rovisco Pais, 1049-001 Lisbon, Portugal.

ORCID-Profile: Joaquim Justino Netto, Luís Reis

Förderung

  • Fundação para a Ciência e Tecnologia
  • Fundação para a Ciência e a Tecnologia
  • Research Unit of Centre for Mechanical and Aerospace Science and Technologies

Zitieren

APA

Pina, F., Vicente, C. M. S., Justino Netto, J., & Reis, L. (2026). Static and Cyclic Mechanical Behavior of 3D-Printed PEEK Under Tensile and Compressive Loads. Polymers, 18(6), 748. https://doi.org/10.3390/polym18060748

Vancouver

Pina F, Vicente CMS, Justino Netto J, Reis L. Static and Cyclic Mechanical Behavior of 3D-Printed PEEK Under Tensile and Compressive Loads. Polymers. 2026;18(6):748. doi:10.3390/polym18060748

BibTeX
@article{Pina2026,
  author = {Pina, Francisco and Vicente, Carlos M S and Justino Netto, Joaquim and Reis, Luís},
  title = {Static and Cyclic Mechanical Behavior of 3D-Printed PEEK Under Tensile and Compressive Loads},
  journal = {Polymers},
  year = {2026},
  volume = {18},
  number = {6},
  pages = {748},
  doi = {10.3390/polym18060748}
}
Kostenlos starten →