Feasibility Study of Suitable Surface Treatments for 3D-Printed Parts to Increase Abrasion Resistance Stability
Polymers · 13.03.2026 · 18 (6) · 703
DOI: 10.3390/polym18060703 ↗Kurz gefasst
Fachartikel in der Zeitschrift Polymers, online erschienen am 13.03.2026. Verfasst von Dominik Fink und 2 weiteren Autor:innen. Beteiligte Einrichtung: Faculty of Mechanical Engineering, Regional Technological Institute, University of West Bohemia, Univerzitni 2732/8, 301 00 Plzen, Czech Republic. Die Arbeit wurde bisher 2-mal zitiert (Crossref) und nennt 38 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Grant Agency of the University of West Bohemia.
Abstract (Originalsprache)
Additive manufacturing technologies such as Multi-Jet Fusion (MJF) enable the production of polymer parts with relatively isotropic mechanical properties; however, their surface condition often limits direct functional application. This study investigates the feasibility of selected surface treatments applied to PA12GB (glass bead-filled PA12) parts manufactured by MJF, with the aim of improving abrasion resistance and temperature-related performance through the modification of surface properties. Five surface treatments were evaluated: base coating (BC), acrylic coating (AC), chemical vapor smoothing (PostPro3D), glasscoat (epoxy-based SiO2 system), and a ceramic-filled 2K epoxy coating. Untreated samples served as a reference. Surface layer thickness, roughness (ISO 21920-2:2021), coefficient of friction (ASTM G99-23), and Shore D hardness (ASTM D2240-15R21) were measured. The results showed significant differences among treatments. Glasscoat and ceramic coatings formed the thickest and hardest layers (≈265 μm and ≈409 μm; Shore D ≈ 84) but exhibited substantially increased friction coefficients. Vapor smoothing and BC produced thinner layers with properties comparable to untreated samples. Acrylic coating reduced surface roughness while moderately increasing hardness. The findings demonstrate that surface treatments substantially alter the tribological and mechanical surface behavior of MJF-printed PA12GB parts. The suitability of a given treatment strongly depends on the intended functional requirements, particularly with respect to friction and surface hardness.
Schlagwörter
Stichwörter der Autor:innen
Autor:innen und Institutionen
- Faculty of Mechanical Engineering, Regional Technological Institute, University of West Bohemia, Univerzitni 2732/8, 301 00 Plzen, Czech Republic.
ORCID-Profile: Dominik Fink, Zdenek Chval, Karel Raz
Förderung
- Grant Agency of the University of West Bohemia
Zitieren
APA
Fink, D., Chval, Z., & Raz, K. (2026). Feasibility Study of Suitable Surface Treatments for 3D-Printed Parts to Increase Abrasion Resistance Stability. Polymers, 18(6), 703. https://doi.org/10.3390/polym18060703
Vancouver
Fink D, Chval Z, Raz K. Feasibility Study of Suitable Surface Treatments for 3D-Printed Parts to Increase Abrasion Resistance Stability. Polymers. 2026;18(6):703. doi:10.3390/polym18060703
BibTeX
@article{Fink2026,
author = {Fink, Dominik and Chval, Zdenek and Raz, Karel},
title = {Feasibility Study of Suitable Surface Treatments for 3D-Printed Parts to Increase Abrasion Resistance Stability},
journal = {Polymers},
year = {2026},
volume = {18},
number = {6},
pages = {703},
doi = {10.3390/polym18060703}
}
EUVIMED