EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Wear Behavior and Multi-Technique Characterization of 3D Printed TPU Under Simulated Pharmaceutical Operating Conditions

Maria Stoica, Marius Gabriel Petrescu iD, Maria Tănase iD, Eugen Laudacescu iD, Elena-Emilia Sirbu iD, Cătălina Călin iD, Gheorghe Brănoiu iD, Ibrahim Naim Ramadan iD

Polymers · 04.03.2026 · 18 (5) · 630

DOI: 10.3390/polym18050630 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Polymers, online erschienen am 04.03.2026. Verfasst von Maria Stoica und 7 weiteren Autor:innen. Beteiligte Einrichtung: Mechanical Engineering Department, Petroleum-Gas University of Ploiești, 100680 Ploiesti, Romania. Die Arbeit wurde bisher 2-mal zitiert (Crossref) und nennt 71 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

This study investigates the wear behavior and multi-technique characterization of 3D printed thermoplastic polyurethane (TPU) intended for friction layers in transmission belts used in pharmaceutical manipulators. Two flexible TPU grades—TPU 51A and TPU 60A—were printed using fused deposition modeling (FDM) with varying printing temperatures (255–265 °C for 51A; 225–235 °C for 60A) and layer counts (three or four layers). Specimens were evaluated for Shore A hardness, wear resistance (mass loss using a Baroid lubricity tester under dry sliding against carton), tensile properties, crystallinity (XRD), chemical structure (FTIR), thermal stability (TGA), and scanning electron microscopy (SEM). The results show that printing parameters significantly influence the mechanical and tribological behavior of the materials. For TPU 51A, increasing the printing temperature to 265 °C and using four layers led to a substantial reduction in cumulative mass loss, although hardness decreased. In contrast, for TPU 60A, higher printing temperature and layer count increased hardness but also resulted in higher wear. Tensile tests indicated that specimens printed with fewer layers exhibited higher yield strength and strain, indicating improved interlayer bonding. XRD analysis confirmed the predominantly amorphous nature of the printed samples, with a reduction in crystallinity compared to the raw filaments. FTIR spectra showed no significant chemical degradation during printing, while thermogravimetric analysis revealed good thermal stability up to approximately 250–260 °C. The results demonstrate that wear behavior is governed by a combination of hardness, interlayer cohesion, and microstructural organization rather than crystallinity alone. Among the investigated conditions, TPU 51A printed at 265 °C with four layers exhibited the most favorable balance between wear resistance and mechanical properties, highlighting its suitability for friction layer applications.

Schlagwörter

Stichwörter der Autor:innen

DSCFDMFTIRSEMTGAXRDhardnesspharmaceuticaltensile testwear

Autor:innen und Institutionen

  • Mechanical Engineering Department, Petroleum-Gas University of Ploiești, 100680 Ploiesti, Romania.
  • Chemistry Department, Petroleum-Gas University of Ploiești, 100680 Ploiesti, Romania.
  • National Institute for Research & Development in Chemistry and Petrochemistry ICECHIM, 060021 Bucharest, Romania.
  • Petroleum Geology and Reservoir Engineering Department, Petroleum-Gas University of Ploiești, 100680 Ploiesti, Romania.

ORCID-Profile: Marius Gabriel Petrescu, Maria Tănase, Eugen Laudacescu, Elena-Emilia Sirbu, Cătălina Călin, Gheorghe Brănoiu, Ibrahim Naim Ramadan

Zitieren

APA

Stoica, M., Petrescu, M. G., Tănase, M., Laudacescu, E., Sirbu, E. E., Călin, C., Brănoiu, G., & Ramadan, I. N. (2026). Wear Behavior and Multi-Technique Characterization of 3D Printed TPU Under Simulated Pharmaceutical Operating Conditions. Polymers, 18(5), 630. https://doi.org/10.3390/polym18050630

Vancouver

Stoica M, Petrescu MG, Tănase M, Laudacescu E, Sirbu EE, Călin C, et al. Wear Behavior and Multi-Technique Characterization of 3D Printed TPU Under Simulated Pharmaceutical Operating Conditions. Polymers. 2026;18(5):630. doi:10.3390/polym18050630

BibTeX
@article{Stoica2026,
  author = {Stoica, Maria and Petrescu, Marius Gabriel and Tănase, Maria and Laudacescu, Eugen and Sirbu, Elena-Emilia and Călin, Cătălina and Brănoiu, Gheorghe and Ramadan, Ibrahim Naim},
  title = {Wear Behavior and Multi-Technique Characterization of 3D Printed TPU Under Simulated Pharmaceutical Operating Conditions},
  journal = {Polymers},
  year = {2026},
  volume = {18},
  number = {5},
  pages = {630},
  doi = {10.3390/polym18050630}
}
Kostenlos starten →