EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

NSGA-II-Based Multi-Objective Optimization of Fused Filament Fabrication Process Parameters for TPU Parts with Chemical Smoothing

Lokeshwaran Srinivasan iD, Lalitha Radhakrishnan iD, Ezhilmaran Veeranan, Faseeulla Khan Mohammad iD, Syed Quadir Moinuddin iD, Hussain Altammar iD

Polymers · 01.02.2026 · 18 (3) · 391

DOI: 10.3390/polym18030391 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Polymers, online erschienen am 01.02.2026. Verfasst von Lokeshwaran Srinivasan und 5 weiteren Autor:innen. Beteiligte Einrichtung: Department of Manufacturing Engineering, College of Engineering Guindy, Anna University, Chennai 600025, India. Die Arbeit wurde bisher 11-mal zitiert (Crossref) und nennt 33 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: King Faisal University, Deanship of Scientific Research, Vice Presidency for Graduate Studies and Scientific Research, King Faisal University, Saudi Arabia.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

In this study, thermoplastic polyurethane (TPU) parts were fabricated using fused filament fabrication (FFF) by varying key process parameters, namely extruder temperature (210–230 °C), layer thickness (200–400 µm), and printing speed (30–50 mm/s). A Box–Behnken experimental design was used to systematically evaluate the combined influence of these parameters on surface roughness (Ra), dimensional deviation (DD), and ultimate tensile strength (UTS). After fabrication, all specimens were subjected to a Tetrahydrofuran (THF)-based chemical smoothing process to modify surface characteristics. Surface roughness measurements showed a substantial reduction after chemical smoothing, with values decreasing from an initial range of 13.17 ± 0.21–15.87 ± 0.23 µm to 4.01 ± 0.18–7.35 ± 0.16 µm, corresponding to an average decrease of approximately 50–72%. Dimensional deviation improved moderately, from 260–420 µm in the as-printed condition to 160–310 µm after post-processing, representing a reduction of about 20–38%. Mechanical testing revealed a consistent increase in UTS following chemical smoothing, with values improving from 30.24–40.30 ± 0.52 MPa to 33.97–47.94 ± 0.36 MPa, yielding an average increase of approximately 10–24%. Then, the experimental data were used for multi-objective optimization of the FFF process parameters, using a non-dominated sorting genetic algorithm (NSGA-II) implemented in Python 3.11, to identify best parameter combinations that provide a balanced surface quality, dimensional accuracy, and mechanical performance.

Schlagwörter

Stichwörter der Autor:innen

additive manufacturingchemical smoothingfused filament fabricationsurface roughnesstetrahydrofuranthermoplastic polyurethane

Autor:innen und Institutionen

  • Department of Manufacturing Engineering, College of Engineering Guindy, Anna University, Chennai 600025, India.
  • Department of Mechanical Engineering, College of Engineering, King Faisal University, Al-Ahsa 31982, Saudi Arabia.

ORCID-Profile: Lokeshwaran Srinivasan, Lalitha Radhakrishnan, Faseeulla Khan Mohammad, Syed Quadir Moinuddin, Hussain Altammar

Förderung

  • King Faisal University
  • Deanship of Scientific Research, Vice Presidency for Graduate Studies and Scientific Research, King Faisal University, Saudi Arabia

Zitieren

APA

Srinivasan, L., Radhakrishnan, L., Veeranan, E., Mohammad, F. K., Moinuddin, S. Q., & Altammar, H. (2026). NSGA-II-Based Multi-Objective Optimization of Fused Filament Fabrication Process Parameters for TPU Parts with Chemical Smoothing. Polymers, 18(3), 391. https://doi.org/10.3390/polym18030391

Vancouver

Srinivasan L, Radhakrishnan L, Veeranan E, Mohammad FK, Moinuddin SQ, Altammar H. NSGA-II-Based Multi-Objective Optimization of Fused Filament Fabrication Process Parameters for TPU Parts with Chemical Smoothing. Polymers. 2026;18(3):391. doi:10.3390/polym18030391

BibTeX
@article{Srinivasan2026,
  author = {Srinivasan, Lokeshwaran and Radhakrishnan, Lalitha and Veeranan, Ezhilmaran and Mohammad, Faseeulla Khan and Moinuddin, Syed Quadir and Altammar, Hussain},
  title = {NSGA-II-Based Multi-Objective Optimization of Fused Filament Fabrication Process Parameters for TPU Parts with Chemical Smoothing},
  journal = {Polymers},
  year = {2026},
  volume = {18},
  number = {3},
  pages = {391},
  doi = {10.3390/polym18030391}
}
Kostenlos starten →