EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Development and Mechanical Characterization of a Jute Fiber-Reinforced Polyester Composite Helmet Produced by Vacuum Infusion

Robson Luis Baleeiro Cardoso iD, Maurício Maia Ribeiro iD, Douglas Santos Silva iD, Raí Felipe Pereira Junio iD, Elza Monteiro Leão Filha, Sergio Neves Monteiro iD, Jean da Silva Rodrigues iD

Polymers · 16.01.2026 · 18 (2) · 235

DOI: 10.3390/polym18020235 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Polymers, online erschienen am 16.01.2026. Verfasst von Robson Luis Baleeiro Cardoso und 6 weiteren Autor:innen. Beteiligte Einrichtung: Materials Engineering Program, Federal Institute of Education, Science and Technology of Pará-IFPA, Avenida Almirante Barroso, 1155, Marco, Belém CEP…. Die Arbeit wurde bisher 3-mal zitiert (Crossref) und nennt 22 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: National Council for Scientific and Technological Development-Brazil (CNPq), National Council for Scientific and Technological Development—Brazil.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

This study presents the development and mechanical characterization of a full-scale helmet manufactured from a polyester matrix composite reinforced with woven jute fabric using vacuum infusion. Laminates with two and four reinforcement layers were produced and assembled using four joining configurations: seamless, stitched, bonded, and hybrid (bonded + stitched). Tensile tests were performed according to ASTM D3039, while frontal and lateral compression tests followed ABNT NBR 7471, aiming to evaluate the influence of laminate thickness and joining strategy on mechanical performance. In tension, the seamless configuration reached maximum loads of 0.80 kN (two layers) and 1.60 kN (four layers), while the hybrid configuration achieved 0.79 kN and 1.43 kN, respectively. Stitched and bonded joints showed lower strength. Under compression, increasing the laminate thickness from two to four layers reduced frontal elongation from 15.09 mm to 9.97 mm and lateral elongation from 13.73 mm to 7.24 mm, corresponding to stiffness gains of 50.3% and 87.3%, respectively. Statistical analysis (ANOVA/Tukey, α = 0.05) confirmed significant effects of thickness and joint configuration. Although vacuum infusion is a well-established process, the novelty of this work lies in its application to a full-scale natural-fiber helmet, combined with a systematic evaluation of joining strategies and a direct correlation between standardized tensile behavior and structural compression performance. The four-layer hybrid laminate exhibited the best balance between strength, stiffness, and deformation capacity.

Schlagwörter

Stichwörter der Autor:innen

jute fibermechanical propertiespolyester compositesustainable materialsvacuum infusion

Autor:innen und Institutionen

  • Materials Engineering Program, Federal Institute of Education, Science and Technology of Pará-IFPA, Avenida Almirante Barroso, 1155, Marco, Belém CEP 66093-020, PA, Brazil.
  • Federal Institute of Education, Science and Technology of Pará-IFPA, Estrada do Icuí Guajará, Ananindeua CEP 67125-000, PA, Brazil.
  • Department of Materials Science, Military Institute of Engineering-IME, Praça General Tibúrcio, 80, Praia Vermelha, Urca, Rio de Janeiro CEP 22290-270, RJ, Brazil.

ORCID-Profile: Robson Luis Baleeiro Cardoso, Maurício Maia Ribeiro, Douglas Santos Silva, Raí Felipe Pereira Junio, Sergio Neves Monteiro, Jean da Silva Rodrigues

Förderung

  • National Council for Scientific and Technological Development-Brazil (CNPq)
  • National Council for Scientific and Technological Development—Brazil

Zitieren

APA

Cardoso, R. L. B., Ribeiro, M. M., Silva, D. S., Junio, R. F. P., Leão Filha, E. M., Monteiro, S. N., & Rodrigues, J. D. S. (2026). Development and Mechanical Characterization of a Jute Fiber-Reinforced Polyester Composite Helmet Produced by Vacuum Infusion. Polymers, 18(2), 235. https://doi.org/10.3390/polym18020235

Vancouver

Cardoso RLB, Ribeiro MM, Silva DS, Junio RFP, Leão Filha EM, Monteiro SN, et al. Development and Mechanical Characterization of a Jute Fiber-Reinforced Polyester Composite Helmet Produced by Vacuum Infusion. Polymers. 2026;18(2):235. doi:10.3390/polym18020235

BibTeX
@article{Cardoso2026,
  author = {Cardoso, Robson Luis Baleeiro and Ribeiro, Maurício Maia and Silva, Douglas Santos and Junio, Raí Felipe Pereira and Leão Filha, Elza Monteiro and Monteiro, Sergio Neves and Rodrigues, Jean da Silva},
  title = {Development and Mechanical Characterization of a Jute Fiber-Reinforced Polyester Composite Helmet Produced by Vacuum Infusion},
  journal = {Polymers},
  year = {2026},
  volume = {18},
  number = {2},
  pages = {235},
  doi = {10.3390/polym18020235}
}
Kostenlos starten →