Surface Activation Using Atmospheric Plasma to Improve PHB Coating Adhesion and Corrosion Resistance of AZ91D Magnesium Alloys
Polymers · 12.01.2026 · 18 (2) · 205
DOI: 10.3390/polym18020205 ↗Kurz gefasst
Fachartikel in der Zeitschrift Polymers, online erschienen am 12.01.2026. Verfasst von Arturo Valenzo und 6 weiteren Autor:innen. Beteiligte Einrichtung: Facultad de Ciencias Químicas e Ingeniera (FCQeI), Universidad Autonóma del Estado de Morelos, Cuernavaca 62210, Morelos, Mexico. Die Arbeit wurde bisher 1-mal zitiert (Crossref) und nennt 23 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: DGAPA, CONACyT.
Abstract (Originalsprache)
Polyhydroxybutyrate (PHB) is considered a coating material capable of limiting the corrosion of biodegradable metallic implants due to its biocompatibility and ability to form a physical barrier. In this study, PHB was deposited on commercial AZ91D magnesium alloy using the spin coating technique. To improve adhesion at the polymer–substrate interface, the magnesium substrates were subjected to atmospheric pressure plasma treatment for different exposure times (5, 10, or 15 min) before coating. The optimal treatment time of 5 min significantly increased substrate wettability and surface free energy, facilitating stronger PHB adhesion. In addition, the PHB coatings were subjected to atmospheric pressure plasma treatment for 5, 10, or 15 s to evaluate potential surface modifications. Corrosion behavior under simulated physiological conditions was assessed via potentiodynamic polarization and electrochemical impedance spectroscopy (EIS) in HANK’s solution at 37 °C. Pull-off tests were used to evaluate the adhesion strength between the coating and the substrate under each treatment condition. The results showed a significant decrease in the corrosion rate (Vcorr), from 4.083 mm/year for bare Mg-AZ91D to 0.001 mm/year when both the substrate and the polymer received plasma treatment. This indicates that the treatment modifies surfaces and improves interfacial bonding, enhancing polymer–metal interaction and producing durable, biocompatible coatings for medical implants.
Schlagwörter
Stichwörter der Autor:innen
Autor:innen und Institutionen
- Facultad de Ciencias Químicas e Ingeniera (FCQeI), Universidad Autonóma del Estado de Morelos, Cuernavaca 62210, Morelos, Mexico.
- Spectroscopy Laboratory, Institute of Physical Sciences, National Autonomous University of Mexico, Cuernavaca 62210, Morelos, Mexico.
- Environmental Engineering and Sustainability Research Laboratory, Polytechnic University of the State of Morelos, Boulevard Cuauhnáhuac 566, Col. Lomas del Texcal, Jiutepec 62574, Morelos, Mexico.
- Centro de Investigaciones en Ingeniería Aplicadas (CIICAp-UAEM), Av. Universidad 1001, Cuernavaca 62209, Morelos, Mexico.
ORCID-Profile: Arturo Valenzo, María Del Pilar Rodríguez-Rojas, Horacio Martínez, Victoria Bustos-Terrones, Alvaro Torres-Islas, Socorro Valdez, Arturo Molina-Ocampo
Förderung
- DGAPA
- CONACyT
Zitieren
APA
Valenzo, A., Rodríguez-Rojas, M. D. P., Martínez, H., Bustos-Terrones, V., Torres-Islas, A., Valdez, S., & Molina-Ocampo, A. (2026). Surface Activation Using Atmospheric Plasma to Improve PHB Coating Adhesion and Corrosion Resistance of AZ91D Magnesium Alloys. Polymers, 18(2), 205. https://doi.org/10.3390/polym18020205
Vancouver
Valenzo A, Rodríguez-Rojas MDP, Martínez H, Bustos-Terrones V, Torres-Islas A, Valdez S, et al. Surface Activation Using Atmospheric Plasma to Improve PHB Coating Adhesion and Corrosion Resistance of AZ91D Magnesium Alloys. Polymers. 2026;18(2):205. doi:10.3390/polym18020205
BibTeX
@article{Valenzo2026,
author = {Valenzo, Arturo and Rodríguez-Rojas, María Del Pilar and Martínez, Horacio and Bustos-Terrones, Victoria and Torres-Islas, Alvaro and Valdez, Socorro and Molina-Ocampo, Arturo},
title = {Surface Activation Using Atmospheric Plasma to Improve PHB Coating Adhesion and Corrosion Resistance of AZ91D Magnesium Alloys},
journal = {Polymers},
year = {2026},
volume = {18},
number = {2},
pages = {205},
doi = {10.3390/polym18020205}
}
EUVIMED