EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

3D-Printed Poly(lactic acid)/Poly(ethylene glycol) Scaffolds with Shape-Memory Effect near Physiological Temperature

Anastasia A Fetisova, Abdullah Bin Firoz iD, Alexandr S Lozhkomoev iD, Elena I Senkina iD, Egor E Ryumin, Maria A Surmeneva, Roman A Surmenev iD

Polymers · 03.01.2026 · 18 (1) · 140

DOI: 10.3390/polym18010140 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Polymers, online erschienen am 03.01.2026. Verfasst von Anastasia A Fetisova und 6 weiteren Autor:innen. Beteiligte Einrichtung: International Research and Development Center Piezo- and Magnetoelectric Materials, Research School of Chemistry and Applied Biomedical Sciences, Nat…. Die Arbeit wurde bisher 8-mal zitiert (Crossref) und nennt 50 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Russian Science Foundation, Tomsk Polytechnic University.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Biocompatible poly(lactic acid) (PLA) was plasticized with poly(ethylene glycol) (PEG) added at concentrations of 10, 15, and 20 wt.% relative to PLA, and then processed into gyroid triply periodic minimal surface (TPMS) scaffolds using fused filament fabrication (FFF) 3D printing. The influence of PEG concentration and gyroid structure (50% infill density) on thermal transitions, crystallinity, and low–temperature shape-memory performance was systematically investigated. The shape-memory effect (SME) of the PLA–based scaffolds was tailored through compositional control and structural design. Shape recovery under thermal activation at 40 °C and 50 °C was examined to reveal the correlation between composition and structure in governing low–temperature shape-memory behavior. The optimal composition (PLA/10 PEG, 50% gyroid infill) achieved shape recovery with a recovery ratio (Rr) of 97 ± 1% at 40 °C within 6 ± 1 min, demonstrating optimal shape-memory activation close to physiological temperature. Structural and morphological changes were characterized using ATR–FTIR, Raman spectroscopy, DSC, XRD, and SEM, providing comprehensive insight into the plasticization of the PLA matrix and its impact on structure–property relationships relevant to bone tissue engineering.

Schlagwörter

Stichwörter der Autor:innen

3D printingadditive manufacturingshape-memory polymertissue engineering

Autor:innen und Institutionen

  • International Research and Development Center Piezo- and Magnetoelectric Materials, Research School of Chemistry and Applied Biomedical Sciences, National Research Tomsk Polytechnic University, 30 Lenina Avenue, Tomsk 6…
  • Physical Materials Science and Composite Materials Centre, Research School of Chemistry and Applied Biomedical Sciences, National Research Tomsk Polytechnic University, 30 Lenina Avenue, Tomsk 634050, Russia.
  • Institute of Strength Physics and Materials Science of Siberian Branch of the Russian Academy of Sciences (ISPMS), 2/4 Akademicheskii Pr., Tomsk 634055, Russia.

ORCID-Profile: Abdullah Bin Firoz, Alexandr S Lozhkomoev, Elena I Senkina, Roman A Surmenev

Förderung

  • Russian Science Foundation
  • Tomsk Polytechnic University

Zitieren

APA

Fetisova, A. A., Bin Firoz, A., Lozhkomoev, A. S., Senkina, E. I., Ryumin, E. E., Surmeneva, M. A., & Surmenev, R. A. (2026). 3D-Printed Poly(lactic acid)/Poly(ethylene glycol) Scaffolds with Shape-Memory Effect near Physiological Temperature. Polymers, 18(1), 140. https://doi.org/10.3390/polym18010140

Vancouver

Fetisova AA, Bin Firoz A, Lozhkomoev AS, Senkina EI, Ryumin EE, Surmeneva MA, et al. 3D-Printed Poly(lactic acid)/Poly(ethylene glycol) Scaffolds with Shape-Memory Effect near Physiological Temperature. Polymers. 2026;18(1):140. doi:10.3390/polym18010140

BibTeX
@article{Fetisova2026,
  author = {Fetisova, Anastasia A and Bin Firoz, Abdullah and Lozhkomoev, Alexandr S and Senkina, Elena I and Ryumin, Egor E and Surmeneva, Maria A and Surmenev, Roman A},
  title = {3D-Printed Poly(lactic acid)/Poly(ethylene glycol) Scaffolds with Shape-Memory Effect near Physiological Temperature},
  journal = {Polymers},
  year = {2026},
  volume = {18},
  number = {1},
  pages = {140},
  doi = {10.3390/polym18010140}
}
Kostenlos starten →