EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Dynamic Mechanical Analysis, Morphology, Physico-Mechanical, and Performance Properties of EPDM/NBR Rubber Blends Containing Chlorosulfonated Polyethylene as a Compatibilizer

Evgeniy Egorov iD, Rakhymzhan Turmanov iD, Rakhmetulla Zhapparbergenov iD, Aslan Oryngaliyev, Nurgali Akylbekov iD, Nurbol Appazov iD, Anton Loshachenko iD, Nikita Glukhoedov iD, Abdirakym Nakyp iD, Nadezhda Semenova

Polymers · 30.12.2025 · 18 (1) · 103

DOI: 10.3390/polym18010103 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Polymers, online erschienen am 30.12.2025. Verfasst von Evgeniy Egorov und 9 weiteren Autor:innen. Beteiligte Einrichtung: Department of Physical Chemistry and Macromolecular Compounds, Faculty of Chemistry and Pharmaceutics, Chuvash State University Named after I.N. Ulya…. Die Arbeit wurde bisher 5-mal zitiert (Crossref) und nennt 83 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: “CT Solutions” LLC, St. Petersburg State University.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

The article studies the influence of chlorosulfonated polyethylene CSM 40 as a compatibilizer on the curing characteristics of the rubber compound, dynamic mechanical analysis, morphology, physico-mechanical and performance properties of vulcanized rubber based on a compound of ethylene propylene diene monomer EPDM S 501A and nitrile butadiene NBR 2645 rubbers. DMA studies indicate that the temperature dependence of tanδ for vulcanizates with and without a compatibilizer based on EPDM S 501A/NBR 2645 at a ratio of 75/25 parts per hundred parts of rubber (phr) has a bimodal character, which indicates the incompatibility of the rubber phases. The temperature dependence for EPDM S 501A/NBR 2645 vulcanizates (25/75 phr) with and without a compatibilizer has a monomodal form, which characterizes the improved compatibility of the rubber phases. SEM showed that a clearly defined microporous structure is observed on a cleavage of vulcanizate sample EPDM/NBR (25/75 phr) without a compatibilizer; with the addition of CSM 40, this feature is retained, but becomes less pronounced. It is shown that vulcanizates containing the compatibilizer CSM 40 are characterized by increased strength properties and hardness compared to vulcanized rubber without a compatibilizer. It was established that the vulcanized rubber based on EPDM S 501A/NBR 2645/CSM 40 (25/75/5 phr) is characterized by the smallest changes in the elastic-strength properties and hardness of vulcanizates after a day of thermo-oxidative aging in air and their weight after exposure to industrial oil I-20A and standard petroleum fluid SZhR-1 at room temperature among vulcanizates based on EPDM S 501A and NBR 2645. The vulcanizate of the rubber compound, including a compound of EPDM/NBR (25/75 phr) with a compatibilizer CSM 40 in an amount of 5 phr (2.88 wt.%), is characterized by stable physico-mechanical properties and improved performance properties. This rubber compound can be used for the manufacture of rubber products operating under the influence of oils and hydrocarbon environments.

Schlagwörter

Stichwörter der Autor:innen

chlorosulfonated polyethylenecompatibilizerdynamic mechanical analysismorphologyperformance propertiesphysico-mechanical propertiesrubber blends

Autor:innen und Institutionen

  • Department of Physical Chemistry and Macromolecular Compounds, Faculty of Chemistry and Pharmaceutics, Chuvash State University Named after I.N. Ulyanov, 15 Moskovsky Prosp., 428015 Cheboksary, Russia.
  • Laboratory of Engineering Profile "Physical and Chemical Methods of Analysis", Korkyt Ata Kyzylorda University, Aiteke bie Str. 29A, 120014 Kyzylorda, Kazakhstan.
  • "CT Solutions" LLP, Medeu District, Ibragimova Street 9, Block B, Office 323, 050032 Almaty, Kazakhstan.
  • Interdisciplinary Resource Centre for Nanotechnology, St. Petersburg State University, 7/9 Universitetskaya Nab., 199034 St. Petersburg, Russia.
  • Department of Synthetic Rubber Technology, Institute of Polymers, Kazan National Research Technological University, 68 K. Marx Str., 420015 Kazan, Russia.
  • Cheboksary Production Association Named after V.I. Chapaev, 1 St. Socialist, 428038 Cheboksary, Russia.

ORCID-Profile: Evgeniy Egorov, Rakhymzhan Turmanov, Rakhmetulla Zhapparbergenov, Nurgali Akylbekov, Nurbol Appazov, Anton Loshachenko, Nikita Glukhoedov, Abdirakym Nakyp

Förderung

  • “CT Solutions” LLC
  • St. Petersburg State University

Zitieren

APA

Egorov, E., Turmanov, R., Zhapparbergenov, R., Oryngaliyev, A., Akylbekov, N., Appazov, N., Loshachenko, A., Glukhoedov, N., Nakyp, A., & Semenova, N. (2025). Dynamic Mechanical Analysis, Morphology, Physico-Mechanical, and Performance Properties of EPDM/NBR Rubber Blends Containing Chlorosulfonated Polyethylene as a Compatibilizer. Polymers, 18(1), 103. https://doi.org/10.3390/polym18010103

Vancouver

Egorov E, Turmanov R, Zhapparbergenov R, Oryngaliyev A, Akylbekov N, Appazov N, et al. Dynamic Mechanical Analysis, Morphology, Physico-Mechanical, and Performance Properties of EPDM/NBR Rubber Blends Containing Chlorosulfonated Polyethylene as a Compatibilizer. Polymers. 2025;18(1):103. doi:10.3390/polym18010103

BibTeX
@article{Egorov2025,
  author = {Egorov, Evgeniy and Turmanov, Rakhymzhan and Zhapparbergenov, Rakhmetulla and Oryngaliyev, Aslan and Akylbekov, Nurgali and Appazov, Nurbol and Loshachenko, Anton and Glukhoedov, Nikita and Nakyp, Abdirakym and Semenova, Nadezhda},
  title = {Dynamic Mechanical Analysis, Morphology, Physico-Mechanical, and Performance Properties of EPDM/NBR Rubber Blends Containing Chlorosulfonated Polyethylene as a Compatibilizer},
  journal = {Polymers},
  year = {2025},
  volume = {18},
  number = {1},
  pages = {103},
  doi = {10.3390/polym18010103}
}
Kostenlos starten →