EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Enhanced Energy Absorption and Flexural Performance of 3D Printed Sandwich Panels Using Slicer-Generated Interlocking Interfaces

Amged Elhassan iD, Hour Alhefeiti, Mdimouna Al Karbi, Fatima Alseiari, Rawan Alshehhi, Waleed Ahmed iD, Al H Al-Marzouqi iD, Noura Al-Mazrouei

Polymers · 29.12.2025 · 18 (1) · 94

DOI: 10.3390/polym18010094 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Polymers, online erschienen am 29.12.2025. Verfasst von Amged Elhassan und 7 weiteren Autor:innen. Beteiligte Einrichtung: Mechanical and Aerospace Engineering Department, UAE University, Al Ain 15551, United Arab Emirates. Die Arbeit wurde bisher 9-mal zitiert (Crossref) und nennt 35 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: UAEU, UAE University.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

This study assessed the effect of slicer-made interlocking joints on 3D printed sandwich panels manufactured through fused filament fabrication (FFF) in terms of flexural properties and energy absorption. Composites were prepared with thermoplastic polyurethane (TPU) as the core material and polyamide (PA), polylactic acid (PLA), polyethylene terephthalate (PET) as skin materials for each of the three composites, respectively. In order to assess the implications of internal geometry, 3D printing was done on five infill topologies (Cross-3D, Grid, Gyroid, Line and Honeycomb) at 20% density. All samples had 20% core density and underwent three point bending testing for flexural testing. It was noted that the Grid and Gyroid cores had the best performance in terms of maximum load capacity based on stretch-dominated behavior while Cross-3D and Honeycomb had lower strengths but stable moments during the bending process. Since Cross-3D topology offered the lowest deflection, it was selected for further experiments with slicer added interlocks at the face–core interface. This study revealed the most notable improvements as gains of up to 15% in peak load, 48% in maximum deflection, and 51% in energy absorption compared with the non-interlocked designs. The PET/TPU interlocked demonstrated the best performance in terms of the energy absorption (2.45 J/mm3) and peak load (272.6 N). In contrast, the PA/TPU interlocked exhibited the best flexibility and ductility with a mid-span deformation of 21.34 mm. These results confirm that slicer-generated interlocking interfaces lead to better load capacity and energy dissipation, providing a lightweight, damage-tolerant design approach for additively manufactured sandwich beams.

Schlagwörter

Stichwörter der Autor:innen

3D printingcompositeflexuralinterlocksandwich

Autor:innen und Institutionen

  • Mechanical and Aerospace Engineering Department, UAE University, Al Ain 15551, United Arab Emirates.
  • Chemical and Petroleum Engineering Department, UAE University, Al Ain 15551, United Arab Emirates.
  • Engineering Requirements Unit, UAE University, Al Ain 15551, United Arab Emirates.

ORCID-Profile: Amged Elhassan, Waleed Ahmed, Al H Al-Marzouqi

Förderung

  • UAEU
  • UAE University

Zitieren

APA

Elhassan, A., Alhefeiti, H., Al Karbi, M., Alseiari, F., Alshehhi, R., Ahmed, W., Al-Marzouqi, A. H., & Al-Mazrouei, N. (2025). Enhanced Energy Absorption and Flexural Performance of 3D Printed Sandwich Panels Using Slicer-Generated Interlocking Interfaces. Polymers, 18(1), 94. https://doi.org/10.3390/polym18010094

Vancouver

Elhassan A, Alhefeiti H, Al Karbi M, Alseiari F, Alshehhi R, Ahmed W, et al. Enhanced Energy Absorption and Flexural Performance of 3D Printed Sandwich Panels Using Slicer-Generated Interlocking Interfaces. Polymers. 2025;18(1):94. doi:10.3390/polym18010094

BibTeX
@article{Elhassan2025,
  author = {Elhassan, Amged and Alhefeiti, Hour and Al Karbi, Mdimouna and Alseiari, Fatima and Alshehhi, Rawan and Ahmed, Waleed and Al-Marzouqi, Al H and Al-Mazrouei, Noura},
  title = {Enhanced Energy Absorption and Flexural Performance of 3D Printed Sandwich Panels Using Slicer-Generated Interlocking Interfaces},
  journal = {Polymers},
  year = {2025},
  volume = {18},
  number = {1},
  pages = {94},
  doi = {10.3390/polym18010094}
}
Kostenlos starten →