Statistical Optimization of Graphene Nanoplatelet-Reinforced Epoxy Nanocomposites via Box–Behnken Design for Superior Flexural and Dynamic Mechanical Performance
Polymers · 03.12.2025 · 17 (23) · 3218
DOI: 10.3390/polym17233218 ↗Kurz gefasst
Fachartikel in der Zeitschrift Polymers, online erschienen am 03.12.2025. Verfasst von Júlia Mendes und 6 weiteren Autor:innen. Beteiligte Einrichtung: Materials and Metallurgical Engineering Department, Federal Fluminense University, Rio de Janeiro 27255-125, Brazil. Die Arbeit wurde bisher 16-mal zitiert (Crossref) und nennt 78 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Carlos Chagas Filho Foundation for Research Support of the State of Rio de Janeiro.
Abstract (Originalsprache)
Graphene nanoplatelets (GNPs) are efficient nanofillers for improving the mechanical and thermal properties of epoxy resins due to their high stiffness, aspect ratio, and interfacial reinforcement ability. This study employs a three-factor, three-level Box–Behnken Design (BBD) to investigate the combined effect of GNP content (0.5–3.5 wt.%), hardener concentration (9–17 phr), and post-curing temperature (30–120 °C) on DGEBA/TETA epoxy nanocomposites. Mechanical, thermal, dynamic mechanical, and morphological characterizations (flexural testing, DMA, TGA, DSC, FTIR, SEM, TEM, and AFM) established structure–property correlations. The optimized formulation (2.0 wt.% GNP, 9 phr hardener, and 120 °C post-curing) exhibited superior reinforcement, with flexural strength of 322.0 ± 12.8 MPa, flexural modulus of 9.7 ± 0.5 GPa, and strain at break of 4.4 ± 0.2%, corresponding to increases of 197%, 155%, and 91% compared with neat epoxy. DMA confirmed a rise in storage modulus from 2.9 to 7.5 GPa and a Tg of 143 °C, while TGA showed a 15 °C improvement in thermal stability. Statistical analysis identified post-curing temperature as the dominant factor governing Tg, stiffness, and thermal stability, with synergistic contributions from GNP content and hardener concentration to the overall network performance. These results surpass those of GO- and CNT-based systems, demonstrating the superior efficiency of GNPs under optimized conditions. The proposed approach provides a robust pathway for developing epoxy nanocomposites with low filler content and enhanced multifunctional performance.
Schlagwörter
Stichwörter der Autor:innen
Autor:innen und Institutionen
- Materials and Metallurgical Engineering Department, Federal Fluminense University, Rio de Janeiro 27255-125, Brazil.
- Brazilian Center for Physics Research, CBPF, Rio de Janeiro 22290-180, Brazil.
- Materials Science Department, Military Institute of Engineering (IME), Rio de Janeiro 22290-270, Brazil.
- Grupo de Durabilidad e Integridad Mecánica de Materiales Estructurales (DIMME), Universidad Rey Juan Carlos, 28933 Madrid, Spain.
ORCID-Profile: Júlia Mendes, Noemi Raquel Checca Huaman, Sergio Neves Monteiro, Teresa Gómez-Del Río, Ulisses Oliveira Costa
Förderung
- Carlos Chagas Filho Foundation for Research Support of the State of Rio de Janeiro
Zitieren
APA
Mendes, J., Magalhães, C. P., Vitorazi, L., Huaman, N. R. C., Monteiro, S. N., Gómez-Del Río, T., & Costa, U. O. (2025). Statistical Optimization of Graphene Nanoplatelet-Reinforced Epoxy Nanocomposites via Box–Behnken Design for Superior Flexural and Dynamic Mechanical Performance. Polymers, 17(23), 3218. https://doi.org/10.3390/polym17233218
Vancouver
Mendes J, Magalhães CP, Vitorazi L, Huaman NRC, Monteiro SN, Gómez-Del Río T, et al. Statistical Optimization of Graphene Nanoplatelet-Reinforced Epoxy Nanocomposites via Box–Behnken Design for Superior Flexural and Dynamic Mechanical Performance. Polymers. 2025;17(23):3218. doi:10.3390/polym17233218
BibTeX
@article{Mendes2025,
author = {Mendes, Júlia and Magalhães, Camila Prudente and Vitorazi, Letícia and Huaman, Noemi Raquel Checca and Monteiro, Sergio Neves and Gómez-Del Río, Teresa and Costa, Ulisses Oliveira},
title = {Statistical Optimization of Graphene Nanoplatelet-Reinforced Epoxy Nanocomposites via Box–Behnken Design for Superior Flexural and Dynamic Mechanical Performance},
journal = {Polymers},
year = {2025},
volume = {17},
number = {23},
pages = {3218},
doi = {10.3390/polym17233218}
}
EUVIMED