EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Enhanced Ablative Performance of Additively Manufactured Thermoplastic Composites for Lightweight Thermal Protection Systems (TPS)

Teodor Adrian Badea iD, Lucia Raluca Maier iD, Alexa-Andreea Crisan

Polymers · 11.09.2025 · 17 (18) · 2462

DOI: 10.3390/polym17182462 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Polymers, online erschienen am 11.09.2025. Verfasst von Teodor Adrian Badea und 2 weiteren Autor:innen. Beteiligte Einrichtung: Composite Materials Laboratory for Aeronautical Field, Romanian Research & Development Institute for Gas Turbines-COMOTI, 220D Iuliu Maniu Av., 06112…. Die Arbeit wurde bisher 3-mal zitiert (Crossref) und nennt 22 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: This work has been funded in part by EvoTurbo Nucleu Program contract no. 31N/2023 and CO-MOTI - Romanian Research & Development Institute for Gas Turbines int…, Romanian Ministry of Research, Innovation and Digitization, COMOTI—Romanian Research & Development Institute for Gas Turbines internal funds.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

The research investigated the potential of five novel additively manufactured (AM) fiber-reinforced thermoplastic composite (FRTPC) configurations as alternatives for ablative thermal protection system (TPS) applications. The thermal stability and ablative behavior of ten samples developed via fused deposition modeling (FDM) three-dimensional (3D) printing out of fire-retardant thermoplastics were investigated using an in-house oxyacetylene torch bench. All samples featured an innovative internal thermal management architecture with three air chambers. Furthermore, the enhancement of thermal benefits was achieved through several approaches: ceramic coating, mechanical hybridization, or continuous fiber reinforcement. For each configuration, two samples were exposed to flame at 1450 ± 50 °C for 30 s and 60 s, respectively, with the front surface subjected to direct exposure at a distance of 100 mm during the ablation tests. Internal temperatures recorded at two back-side contact points remained below 50 °C, well under the 180 °C maximum allowable back-face temperature for TPS during testing. Continuous reinforced configurations 4 and 5 displayed higher thermal stability the lowest values in terms of thickness, mass loss, and recession rates. Both configurations showed half of the weight losses measured for the other tested configurations, ranging from approximately 5% (30 s) to 10–12% (60 s), confirming the trend observed in the thickness loss measurements. However, continuous glass-reinforced configuration 5 exhibited the lowest weight loss values for both exposure durations, benefiting from its non-combustible nature, low thermal conductivity, and high abrasion resistance intrinsic characteristics. In particular, the Al2O3 surface coated configuration 1 showed a mass loss comparable to reinforced configurations, indicating that an enhanced surface coat adhesion could provide a potential benefit. A key outcome of the study was the synergistic effect of the novel air chamber architecture, which reduces thermal conductivity by forming small internal air pockets, combined with the continuous front-wall fiber reinforcement functioning as a thermal and abrasion barrier. This remains a central focus for future research and optimization.

Schlagwörter

Stichwörter der Autor:innen

FRTPCablative TPSadditive manufacturingoxyacetylene torchsurface coating

Autor:innen und Institutionen

  • Composite Materials Laboratory for Aeronautical Field, Romanian Research & Development Institute for Gas Turbines-COMOTI, 220D Iuliu Maniu Av., 061126 Bucharest, Romania.

ORCID-Profile: Teodor Adrian Badea, Lucia Raluca Maier

Förderung

  • This work has been funded in part by EvoTurbo Nucleu Program contract no. 31N/2023 and CO-MOTI - Romanian Research & Development Institute for Gas Turbines int…
  • Romanian Ministry of Research, Innovation and Digitization
  • COMOTI—Romanian Research & Development Institute for Gas Turbines internal funds

Zitieren

APA

Badea, T. A., Maier, L. R., & Crisan, A. A. (2025). Enhanced Ablative Performance of Additively Manufactured Thermoplastic Composites for Lightweight Thermal Protection Systems (TPS). Polymers, 17(18), 2462. https://doi.org/10.3390/polym17182462

Vancouver

Badea TA, Maier LR, Crisan AA. Enhanced Ablative Performance of Additively Manufactured Thermoplastic Composites for Lightweight Thermal Protection Systems (TPS). Polymers. 2025;17(18):2462. doi:10.3390/polym17182462

BibTeX
@article{Badea2025,
  author = {Badea, Teodor Adrian and Maier, Lucia Raluca and Crisan, Alexa-Andreea},
  title = {Enhanced Ablative Performance of Additively Manufactured Thermoplastic Composites for Lightweight Thermal Protection Systems (TPS)},
  journal = {Polymers},
  year = {2025},
  volume = {17},
  number = {18},
  pages = {2462},
  doi = {10.3390/polym17182462}
}
Kostenlos starten →