EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Three-Dimensional-Printed Polymer–Polymer Composite Electrolytes for All-Solid-State Li Metal Batteries

Hao Wang, Xin Xiong, Huie Hu, Sijie Liu

Polymers · 30.08.2025 · 17 (17) · 2369

DOI: 10.3390/polym17172369 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Polymers, online erschienen am 30.08.2025. Verfasst von Hao Wang und 3 weiteren Autor:innen. Beteiligte Einrichtung: Foundation Department, Naval University of Engineering, Wuhan 430033, China. Die Arbeit wurde bisher 3-mal zitiert (Crossref) und nennt 54 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Shenzhen Lithium Battery Electrode Active Materials Engineering Laboratory Enhancement, Shenzhen Development and Reform Commission.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

High-performance batteries for military and extreme environment applications require alternatives to conventional liquid lithium-ion batteries (LIBs), which suffer from poor low-temperature performance and safety risks. All-solid-state lithium batteries (ASSLBs) offer enhanced safety and superior low-temperature capability. In this work, we designed and fabricated composite solid-state electrolytes using polyvinylidene fluoride (PVDF) and polyacrylic acid (PAA) as polymer matrices, N,N-dimethylformamide (DMF) as the solvent, and lithium bis(trifluoromethane sulfonimide) (LiTFSI) as the lithium salt. Composite solutions with varying PAA mass ratios were prepared. Advanced three-dimensional (3D) printing technology enabled the rapid and precise fabrication of electrolyte membranes. An ionic conductivity of about 2.71 × 10−4 S cm−1 at 25 °C, high mechanical strength, and good thermal properties can be achieved through component and 3D printing process optimization. Assembled LiCoO2||PVDF@PAA||Li ASSLBs delivered an initial discharge capacity of 165.3 mAh/g at 0.1 mA cm−2 (room temperature), maintaining 98% capacity retention after 300 cycles. At 0 °C, these cells provided 157.4 mAh/g initial capacity with 85% retention over 100 cycles at 0.1 mA cm−2. This work identifies the optimal PAA ratio for enhanced electrochemical performance and demonstrates the viability of 3D printing for advanced ASSLB manufacturing.

Schlagwörter

Stichwörter der Autor:innen

3D printingall-solid-state lithium batteries (ASSLBs)polyacrylic acid (PAA)polyvinylidene fluoride (PVDF)solid polymer electrolytes (SPEs)

Autor:innen und Institutionen

  • Foundation Department, Naval University of Engineering, Wuhan 430033, China.
  • Research Institute of Tsinghua University in Shenzhen, Shenzhen 518000, China.
  • Institute of Nuclear and New Energy Technology, Tsinghua University, Beijing 100084, China.

Förderung

  • Shenzhen Lithium Battery Electrode Active Materials Engineering Laboratory Enhancement
  • Shenzhen Development and Reform Commission

Zitieren

APA

Wang, H., Xiong, X., Hu, H., & Liu, S. (2025). Three-Dimensional-Printed Polymer–Polymer Composite Electrolytes for All-Solid-State Li Metal Batteries. Polymers, 17(17), 2369. https://doi.org/10.3390/polym17172369

Vancouver

Wang H, Xiong X, Hu H, Liu S. Three-Dimensional-Printed Polymer–Polymer Composite Electrolytes for All-Solid-State Li Metal Batteries. Polymers. 2025;17(17):2369. doi:10.3390/polym17172369

BibTeX
@article{Wang2025,
  author = {Wang, Hao and Xiong, Xin and Hu, Huie and Liu, Sijie},
  title = {Three-Dimensional-Printed Polymer–Polymer Composite Electrolytes for All-Solid-State Li Metal Batteries},
  journal = {Polymers},
  year = {2025},
  volume = {17},
  number = {17},
  pages = {2369},
  doi = {10.3390/polym17172369}
}
Kostenlos starten →