Molded Part Warpage Optimization Using Inverse Contouring Method
Polymers · 22.08.2025 · 17 (17) · 2278
DOI: 10.3390/polym17172278 ↗Kurz gefasst
Fachartikel in der Zeitschrift Polymers, online erschienen am 22.08.2025. Verfasst von Damir Godec und 3 weiteren Autor:innen. Beteiligte Einrichtung: Faculty of Mechanical Engineering and Naval Architecture, University of Zagreb, HR-10000 Zagreb, Croatia. Die Arbeit wurde bisher 7-mal zitiert (Crossref) und nennt 109 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: CEEPUS Agency.
Abstract (Originalsprache)
Warpage is among the most prevalent defects affecting injection molded parts. In this study, we aimed to develop methods to minimize warpage through mold design. Common strategies include matching the cavity geometry to the intended shape of the part, adjusting cavity dimensions to offset material shrinkage, and optimizing the cooling system and critical injection molding parameters. These optimization methods can offer significant improvements, but recently introduced methods that optimize the molded part and mold cavity shape result in higher levels of warpage reduction. In these methods, optimization of the shape of the molded part is achieved by shaping it in the opposite direction of warpage—a method known as inverse contouring. Inverse contouring of molded parts is a design technique in which mold cavities are intentionally modified to incorporate compensatory geometric deviations in regions anticipated to exhibit significant warpage. The final result after molded part ejection and warpage is a significant reduction in deviations between the warped and reference molded part geometries. In this study, a two-step approach for minimizing warpage was used: the first step was optimizing the most significant injection molding parameters, and the second was inverse contouring. In the first step, Response Surface Methodology (RSM) and Autodesk Moldflow Insight 2023 simulations were used to optimize molded part warpage based on three processing parameters: melt temperature, target mold temperature, and coolant temperature. For improved accuracy, a Computer-Aided Design (CAD) model of the warped molded part was exported into ZEISS Inspect 2023 software and aligned with the reference CAD geometry of the molded part. The maximal warpage value after the initial simulation was 1.85 mm based on Autodesk Moldflow Insight simulations and 1.67 mm based on ZEISS Inspect alignment. After RSM optimization, the maximal warpage was 0.73 mm. In the second step, inverse contouring was performed on the molded part, utilizing the initial injection molding simulation results to further reduce warpage. In this step, the CAD model of the redesigned, inverse-contoured molded part was imported into Moldflow Insight to conduct a second iteration of the injection molding simulation. The simulation results were exported into ZEISS Inspect software for a final analysis and comparison with the reference CAD model. The warpage values after inverse contouring were reduced within the range of ±0.30 mm, which represents a significant decrease in warpage of approximately 82%. Both steps are presented in a case study on an injection molded part made of polybutylene terephthalate (PBT) with 30% glass fiber (GF).
Schlagwörter
Stichwörter der Autor:innen
Autor:innen und Institutionen
- Faculty of Mechanical Engineering and Naval Architecture, University of Zagreb, HR-10000 Zagreb, Croatia.
- Yazaki-Europe Limited, HR-10000 Zagreb, Croatia.
- Faculty of Manufacturing Technologies with a seat in Prešov, Technical University Košice, 08001 Prešov, Slovakia.
- Faculty of Technology, Tomas Bata University in Zlin, Vavreckova 5669, 760 01 Zlin, Czech Republic.
ORCID-Profile: Damir Godec, Mislav Tujmer, Katarina Monkova
Förderung
- CEEPUS Agency
Zitieren
APA
Godec, D., Panđa, F., Tujmer, M., & Monkova, K. (2025). Molded Part Warpage Optimization Using Inverse Contouring Method. Polymers, 17(17), 2278. https://doi.org/10.3390/polym17172278
Vancouver
Godec D, Panđa F, Tujmer M, Monkova K. Molded Part Warpage Optimization Using Inverse Contouring Method. Polymers. 2025;17(17):2278. doi:10.3390/polym17172278
BibTeX
@article{Godec2025,
author = {Godec, Damir and Panđa, Filip and Tujmer, Mislav and Monkova, Katarina},
title = {Molded Part Warpage Optimization Using Inverse Contouring Method},
journal = {Polymers},
year = {2025},
volume = {17},
number = {17},
pages = {2278},
doi = {10.3390/polym17172278}
}
EUVIMED