EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Manufacturing of Polymer–Metal Composite by Fused Filament Fabrication: Adhesion of PLA and PETG on Aluminum

Miguel Campos-Jurado iD, Óscar Rodríguez-Alabanda iD, Guillermo Guerrero-Vacas iD

Polymers · 13.08.2025 · 17 (16) · 2210

DOI: 10.3390/polym17162210 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Polymers, online erschienen am 13.08.2025. Verfasst von Miguel Campos-Jurado und 2 weiteren Autor:innen. Beteiligte Einrichtung: Department of Mechanical Engineering, Higher Polytechnic School, University of Córdoba, Rabanales University Campus, 14014 Córdoba, Spain. Die Arbeit wurde bisher 5-mal zitiert (Crossref) und nennt 29 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: OTRI technology-transfer contract of the Universidad de Córdoba entitled “Evaluation of the efficiency of sol-gel ceramic coatings for non-stick applications”.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

The formation of metal–polymer composites by 3D printing PLA and PETG onto EN AW-5182 H111 aluminum substrates without the use of adhesives was investigated. Four surface treatments were evaluated on the metal substrate (fine sanding, coarse sanding, abrasive blasting, and acid etching), over which a polymer primer—prepared from PLA and PETG solutions—was applied. Subsequently, test specimens were fabricated using the same polymer through material extrusion (MEX) with filaments. Adhesion strength between the printed polymer and the metal substrate was assessed through perpendicular tensile, lap shear, and three-point bending tests. The 16-condition experimental matrix combined surface treatment, primer thickness, and bed temperature and was replicated for each test. Peak tensile and shear strengths confirmed the effectiveness of the proposed strategy, with PETG consistently showing a higher interfacial performance than PLA. ANOVA analysis identifies primer layer thickness (p = 0.023) and loading type (p = 0.031) as statistically significant variables. The results suggest that either abrasive or acid pretreatment, combined with a primer thickness ≥ 80 µm and moderate bed temperatures (65 °C for PLA and 90 °C for PETG), enables the fabrication of robust metal–polymer joints, which are particularly resistant to shear stress and suitable for industrial applications.

Schlagwörter

Stichwörter der Autor:innen

PETGPLAaluminum–magnesium alloymetal–polymer bondingmetal–polymer compositeshear testsurface treatmenttensile test

Autor:innen und Institutionen

  • Department of Mechanical Engineering, Higher Polytechnic School, University of Córdoba, Rabanales University Campus, 14014 Córdoba, Spain.

ORCID-Profile: Miguel Campos-Jurado, Óscar Rodríguez-Alabanda, Guillermo Guerrero-Vacas

Förderung

  • OTRI technology-transfer contract of the Universidad de Córdoba entitled “Evaluation of the efficiency of sol-gel ceramic coatings for non-stick applications”

Zitieren

APA

Campos-Jurado, M., Rodríguez-Alabanda, Ó., & Guerrero-Vacas, G. (2025). Manufacturing of Polymer–Metal Composite by Fused Filament Fabrication: Adhesion of PLA and PETG on Aluminum. Polymers, 17(16), 2210. https://doi.org/10.3390/polym17162210

Vancouver

Campos-Jurado M, Rodríguez-Alabanda Ó, Guerrero-Vacas G. Manufacturing of Polymer–Metal Composite by Fused Filament Fabrication: Adhesion of PLA and PETG on Aluminum. Polymers. 2025;17(16):2210. doi:10.3390/polym17162210

BibTeX
@article{CamposJurado2025,
  author = {Campos-Jurado, Miguel and Rodríguez-Alabanda, Óscar and Guerrero-Vacas, Guillermo},
  title = {Manufacturing of Polymer–Metal Composite by Fused Filament Fabrication: Adhesion of PLA and PETG on Aluminum},
  journal = {Polymers},
  year = {2025},
  volume = {17},
  number = {16},
  pages = {2210},
  doi = {10.3390/polym17162210}
}
Kostenlos starten →