EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Effects of Post-Curing on Mechanical Strength and Cytotoxicity of Stereolithographic Methacrylate Resins

Alfredo Rondinella, Matteo Zanocco iD, Alex Lanzutti iD, Wenliang Zhu iD, Enrico Greco iD, Elia Marin iD

Polymers · 02.08.2025 · 17 (15) · 2132

DOI: 10.3390/polym17152132 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Polymers, online erschienen am 02.08.2025. Verfasst von Alfredo Rondinella und 5 weiteren Autor:innen. Beteiligte Einrichtung: Department Polytechnic of Engineering and Architecture, University of Udine, 33100 Udine, Italy. Die Arbeit wurde bisher 7-mal zitiert (Crossref) und nennt 31 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

This study investigated the influence of curing temperature and time on both the mechanical properties and cytotoxicity of stereolithographic polymethyl methacrylate (PMMA) resin. After printing using stereolithographic equipment, the resin was cured at 45 °C, 60 °C, and 75 °C for up to 120 min. Our results reveal that the mechanical properties achieved a peak after approximately 30 min of curing at the two highest temperatures, followed by a subsequent decrease, while curing at 45 °C resulted in a constant increase in mechanical properties up to 120 min. Testing with S. epidermidis and E. coli exhibited a bland antibacterial effect, with the number of living bacteria increasing with both the time and temperature of curing. To assess potential cytotoxicity, the materials were also tested with human fibroblasts, and the trends observed were similar to what was previously seen for both bacteria strains. Interestingly, an association was observed between the intensity ratio of two Raman bands (around 2920 and 2945 cm−1), indicative of long-PMMA-chain formation and cytotoxicity. This finding suggests that Raman spectroscopy has the potential to serve as a viable method for estimating the cytotoxicity of 3D printed PMMA objects.

Schlagwörter

Stichwörter der Autor:innen

PMMARaman spectroscopycuringcytotoxicitymechanical propertiesstereolithographic resin

Autor:innen und Institutionen

  • Department Polytechnic of Engineering and Architecture, University of Udine, 33100 Udine, Italy.
  • Ceramic Physics Laboratory, Faculty of Materials Science and Engineering, Kyoto Institute of Technology, Sakyo-ku, Matsugasaki, Kyoto 606-8585, Japan.
  • Institute for the Advanced Study of Culture and the Environment (IASCE), University of South Florida, 4202 E. Fowler Ave, Tampa, FL 33620, USA.
  • National Interuniversity Consortium of Materials Science and Technology (INSTM), Via G. Giusti 9, 50121 Firenze, Italy.
  • Biomaterials Engineering Laboratory, Faculty of Materials Science and Engineering, Kyoto Institute of Technology, Sakyo-ku, Matsugasaki, Kyoto 606-8585, Japan.
  • Biomedical Research Center, Kyoto Institute of Technology, Sakyo-ku, Matsugasaki, Kyoto 606-8585, Japan.

ORCID-Profile: Matteo Zanocco, Alex Lanzutti, Wenliang Zhu, Enrico Greco, Elia Marin

Zitieren

APA

Rondinella, A., Zanocco, M., Lanzutti, A., Zhu, W., Greco, E., & Marin, E. (2025). Effects of Post-Curing on Mechanical Strength and Cytotoxicity of Stereolithographic Methacrylate Resins. Polymers, 17(15), 2132. https://doi.org/10.3390/polym17152132

Vancouver

Rondinella A, Zanocco M, Lanzutti A, Zhu W, Greco E, Marin E. Effects of Post-Curing on Mechanical Strength and Cytotoxicity of Stereolithographic Methacrylate Resins. Polymers. 2025;17(15):2132. doi:10.3390/polym17152132

BibTeX
@article{Rondinella2025,
  author = {Rondinella, Alfredo and Zanocco, Matteo and Lanzutti, Alex and Zhu, Wenliang and Greco, Enrico and Marin, Elia},
  title = {Effects of Post-Curing on Mechanical Strength and Cytotoxicity of Stereolithographic Methacrylate Resins},
  journal = {Polymers},
  year = {2025},
  volume = {17},
  number = {15},
  pages = {2132},
  doi = {10.3390/polym17152132}
}
Kostenlos starten →