EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Additive Manufacturing Meets Gear Mechanics: Understanding Abrasive Wear Evolution in FDM-Printed Gears

Robert Ciobanu iD, George Arhip, Octavian Donțu, Ciprian Ion Rizescu iD, Bogdan Grămescu iD

Polymers · 29.06.2025 · 17 (13) · 1810

DOI: 10.3390/polym17131810 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Polymers, online erschienen am 29.06.2025. Verfasst von Robert Ciobanu und 4 weiteren Autor:innen. Beteiligte Einrichtung: Department of Mechatronics and Precision Mechanics, Faculty of Mechanical Engineering and Mechatronics, National University of Science and Technology…. Die Arbeit wurde bisher 14-mal zitiert (Crossref) und nennt 39 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

This paper presents an analysis of the abrasive wear influence on the tooth flank geometry of plastic gear wheels, emphasizing the contribution of tooth stiffness to the observed changes. The study examined gear wheels made from polylactic acid (PLA) with wall thicknesses of 0.6 mm, 1.0 mm and 2.4 mm, manufactured using FDM technology. A standard layer height of 0.2 mm was chosen as it offers a balance between good precision and reasonable printing times. The PLA gear wheels were tested for wear in a meshing configuration with a metallic reference gear. The results indicate that wear intensity increases as tooth stiffness decreases, suggesting an inverse proportionality between abrasive wear and tooth stiffness. In all tested cases, the tooth tip was more affected by abrasive wear compared to the rest of the profile. The analysis establishes that sliding velocity has the greatest influence on the abrasive wear characteristics of the evaluated gears. Based on experimental findings, a mathematical model was developed for simulating abrasive wear in plastic gears, with scalability across various manufacturing technologies. For PLA gears, both experimental and simulated data confirm that full tooth infill is essential for functional durability.

Schlagwörter

Stichwörter der Autor:innen

3D scanningabrasive wearadditive manufacturinggear wheelspolylactic acid

Autor:innen und Institutionen

  • Department of Mechatronics and Precision Mechanics, Faculty of Mechanical Engineering and Mechatronics, National University of Science and Technology POLITEHNICA Bucharest, 060042 Bucharest, Romania.

ORCID-Profile: Robert Ciobanu, Ciprian Ion Rizescu, Bogdan Grămescu

Zitieren

APA

Ciobanu, R., Arhip, G., Donțu, O., Rizescu, C. I., & Grămescu, B. (2025). Additive Manufacturing Meets Gear Mechanics: Understanding Abrasive Wear Evolution in FDM-Printed Gears. Polymers, 17(13), 1810. https://doi.org/10.3390/polym17131810

Vancouver

Ciobanu R, Arhip G, Donțu O, Rizescu CI, Grămescu B. Additive Manufacturing Meets Gear Mechanics: Understanding Abrasive Wear Evolution in FDM-Printed Gears. Polymers. 2025;17(13):1810. doi:10.3390/polym17131810

BibTeX
@article{Ciobanu2025,
  author = {Ciobanu, Robert and Arhip, George and Donțu, Octavian and Rizescu, Ciprian Ion and Grămescu, Bogdan},
  title = {Additive Manufacturing Meets Gear Mechanics: Understanding Abrasive Wear Evolution in FDM-Printed Gears},
  journal = {Polymers},
  year = {2025},
  volume = {17},
  number = {13},
  pages = {1810},
  doi = {10.3390/polym17131810}
}
Kostenlos starten →