EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Drilling Machinability of Glass, Basalt, and Hybrid Epoxy Composites: Thrust Force, Thermal Load, and Hole Quality

Eser Yarar iD, Mehmet İskender Özsoy iD, Sinan Fidan iD, Satılmış Ürgün iD, Mustafa Özgür Bora iD

Polymers · 13.06.2025 · 17 (12) · 1643

DOI: 10.3390/polym17121643 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Polymers, online erschienen am 13.06.2025. Verfasst von Eser Yarar und 4 weiteren Autor:innen. Beteiligte Einrichtung: Department of Mechanical Engineering, Faculty of Engineering, Kocaeli University, Kocaeli 41380, Türkiye. Die Arbeit wurde bisher 9-mal zitiert (Crossref) und nennt 44 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Kocaeli University Scientific Research Projects Coordination Unit.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

The drilling machinability of glass fiber G14, basalt fiber B14, and two hybrid laminates (B4G6B4, G4B6G4) was evaluated through 36 full-factorial experiments employing an HSS-G drill, three spindle speeds (715, 1520, 3030 rpm), and three feed rates (0.1–0.3 mm rev−1). Peak thrust force varied from 65.8 N for B14 at 0.1 mm rev−1 to 174.3 N for G14 at 0.3 mm rev−1; hybrids occupied the intermediate range of 101–163 N. Infra-red thermography recorded maximum drill temperatures of 110–120 °C for G14, almost double those of B14, while both hybrids attenuated hotspots to below 90 °C. ANOVA attributed 73.4% of thrust force variance to feed rate, with material type and spindle speed contributing 15.5% and 1.7%, respectively; for temperature, material type governed 41.5% of variability versus 17.0% for speed. Dimensional quality tests revealed that the symmetric hybrid G4B6G4 maintained entrance and exit diameters within ±2% of the nominal 6 mm, whereas B4G6B4 over-expansion exceeded 8% at the lowest feed and G14 exit diameters grew to 6.1 mm at 0.3 mm rev−1. Integrating basalt compliance with glass stiffness, therefore, halves thrust force relative to G14, suppresses delamination and overheating, and offers a practical strategy to prolong tool life and improve hole quality in multi-material composite structures. These insights guide parameter selection for lightweight hybrid composites in aerospace, renewable-energy installations, and marine components worldwide.

Schlagwörter

Stichwörter der Autor:innen

drilling machinabilityhigh temperaturehole qualityhybrid glass–basalt laminatesthermal responsethrust force

Autor:innen und Institutionen

  • Department of Mechanical Engineering, Faculty of Engineering, Kocaeli University, Kocaeli 41380, Türkiye.
  • Department of Mechanical Engineering, Faculty of Engineering, Sakarya University, Sakarya 54050, Türkiye.
  • Department of Airframe and Powerplant Maintenance, Faculty of Aeronautics and Astronautics, Kocaeli University, Kocaeli 41001, Türkiye.
  • Department of Aviation Electrics and Electronics, Faculty of Aeronautics and Astronautics, Kocaeli University, Kocaeli 41001, Türkiye.

ORCID-Profile: Eser Yarar, Mehmet İskender Özsoy, Sinan Fidan, Satılmış Ürgün, Mustafa Özgür Bora

Förderung

  • Kocaeli University Scientific Research Projects Coordination Unit

Zitieren

APA

Yarar, E., Özsoy, M. İ., Fidan, S., Ürgün, S., & Bora, M. Ö. (2025). Drilling Machinability of Glass, Basalt, and Hybrid Epoxy Composites: Thrust Force, Thermal Load, and Hole Quality. Polymers, 17(12), 1643. https://doi.org/10.3390/polym17121643

Vancouver

Yarar E, Özsoy Mİ, Fidan S, Ürgün S, Bora MÖ. Drilling Machinability of Glass, Basalt, and Hybrid Epoxy Composites: Thrust Force, Thermal Load, and Hole Quality. Polymers. 2025;17(12):1643. doi:10.3390/polym17121643

BibTeX
@article{Yarar2025,
  author = {Yarar, Eser and Özsoy, Mehmet İskender and Fidan, Sinan and Ürgün, Satılmış and Bora, Mustafa Özgür},
  title = {Drilling Machinability of Glass, Basalt, and Hybrid Epoxy Composites: Thrust Force, Thermal Load, and Hole Quality},
  journal = {Polymers},
  year = {2025},
  volume = {17},
  number = {12},
  pages = {1643},
  doi = {10.3390/polym17121643}
}
Kostenlos starten →