EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Discharge Energy Versus Exposure Time in Atmospheric-Pressure Air Plasma Surface Treatment of Polyimide and Polyamide 6 Films

Iustina Hatescu, Cătălin Borcia iD, Roxana Ciobanu, Gabriela Borcia iD

Polymers · 19.05.2025 · 17 (10) · 1394

DOI: 10.3390/polym17101394 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Polymers, online erschienen am 19.05.2025. Verfasst von Iustina Hatescu und 3 weiteren Autor:innen. Beteiligte Einrichtung: Iasi Plasma Advanced Research Center (IPARC), Faculty of Physics, Alexandru Ioan Cuza University, Blvd. Carol I No. 11, 700506 Iasi, Romania. Die Arbeit wurde bisher 7-mal zitiert (Crossref) und nennt 62 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: project (EXCELENT-UAIC).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Polyimide (PI) and polyamide 6 (PA6) films are treated under exposure times of 0.5 s and 1.0 s, and energy levels of 1.5, 2.0, and 2.3 mJ/pulse. PI exhibits the most substantial improvement in wettability and adhesion-related properties compared to PA6 and other studied polar polymers. The threshold level for stable surface modification is reduced, achieving a minimum water contact angle of 45°. The stability is markedly enhanced, with aged PI surfaces showing a 40% relative increase in adhesion work compared to untreated samples. The oxygen content on the PI surface reaches 22 at. %, surpassing the maximum of 18 at. % O observed for PA6. The surface roughness of PI increases by approximately a factor of 2, while PA6 shows an average increase of only 25%, attributed to higher ablation rates in the amorphous phase compared to the crystalline phase. The degree of surface modification achieved with [1.0 s; 1.5 mJ] treatment parameters is comparable to that with [0.5 s; 2.0 mJ], demonstrating that higher discharge energy can effectively shorten the required exposure time. This plasma treatment, even at very short exposure times, enables significant enhancement of the surface properties of PI, typically characterized by high chemical stability.

Schlagwörter

Stichwörter der Autor:innen

adhesionatmospheric pressure plasmaoxidationpolyamide 6polyimidewettability

Autor:innen und Institutionen

  • Iasi Plasma Advanced Research Center (IPARC), Faculty of Physics, Alexandru Ioan Cuza University, Blvd. Carol I No. 11, 700506 Iasi, Romania.

ORCID-Profile: Cătălin Borcia, Gabriela Borcia

Förderung

  • project (EXCELENT-UAIC)

Zitieren

APA

Hatescu, I., Borcia, C., Ciobanu, R., & Borcia, G. (2025). Discharge Energy Versus Exposure Time in Atmospheric-Pressure Air Plasma Surface Treatment of Polyimide and Polyamide 6 Films. Polymers, 17(10), 1394. https://doi.org/10.3390/polym17101394

Vancouver

Hatescu I, Borcia C, Ciobanu R, Borcia G. Discharge Energy Versus Exposure Time in Atmospheric-Pressure Air Plasma Surface Treatment of Polyimide and Polyamide 6 Films. Polymers. 2025;17(10):1394. doi:10.3390/polym17101394

BibTeX
@article{Hatescu2025,
  author = {Hatescu, Iustina and Borcia, Cătălin and Ciobanu, Roxana and Borcia, Gabriela},
  title = {Discharge Energy Versus Exposure Time in Atmospheric-Pressure Air Plasma Surface Treatment of Polyimide and Polyamide 6 Films},
  journal = {Polymers},
  year = {2025},
  volume = {17},
  number = {10},
  pages = {1394},
  doi = {10.3390/polym17101394}
}
Kostenlos starten →