EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Eco-Friendly Polypropylene Composites Reinforced with Cellulose Fibers and Silica Nanoparticles

Rinat M Iskakov iD, Aigul S Bukanova, Altynay S Kalauova, Fazilat B Kairliyeva iD, Alimzhan N Nauashev, Gulbarshin K Shambilova, Ivan M Obidin iD, Mikhail S Kuzin iD, Dmitryi N Chernenko, Timofey D Patsaev iD, Pavel S Gerasimenko iD, Igor S Makarov iD und 1 weitere

Polymers · 08.05.2025 · 17 (10) · 1290

DOI: 10.3390/polym17101290 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Polymers, online erschienen am 08.05.2025. Verfasst von Rinat M Iskakov und 12 weiteren Autor:innen. Beteiligte Einrichtung: Institute of Petrochemical Engineering and Ecology Named After N.K. Nadirov, Atyrau Oil and Gas University Named After S. Utebayev, M. Baimukhanov St…. Die Arbeit wurde bisher 7-mal zitiert (Crossref) und nennt 81 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: A.V. Topchiev Institute of Petrochemical Synthesis, Kurchatov Institute, State Program of TIPS RAS.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

In this study, polymer composites based on a polypropylene (PP) matrix with the addition of cellulose and ES-40, used as a silica precursor, were investigated. These composites were designed to achieve enhanced biodegradability through the incorporation of bioavailable cellulose and to enable subsequent carbonization into carbon–silicon carbide systems. Rheological investigations revealed that the multicomponent mixtures exhibited pseudoplastic behavior over the shear rate range typical of injection molding, ensuring process stability without additional plasticization. Morphological analysis demonstrated that an optimal balance of PP, cellulose, and ES-40 promoted the formation of a three-dimensional network structure, leading to a significant increase in flexural modulus at the equal flexural strength despite some reduction in tensile strength. It was further shown that substituting fibrous cellulose with microcrystalline cellulose improved the composite homogeneity, thereby enhancing the density and mechanical properties, especially in systems with low polymer contents. Preliminary pyrolysis experiments indicated that these injection-molded composites can serve as precursors for fabricating bulk thermally stable products containing silicon carbide particles. The obtained results underscore the high potential of the developed materials for applications in conventional injection molding, the possibility of additive manufacturing, and processes requiring subsequent carbonization.

Schlagwörter

Stichwörter der Autor:innen

amorphizationcellulosecompositescrystallinitydynamic thermomechanical analysisoligosiloxanespolycondensationpolypropylenerheologysol–gel synthesis

Autor:innen und Institutionen

  • Institute of Petrochemical Engineering and Ecology Named After N.K. Nadirov, Atyrau Oil and Gas University Named After S. Utebayev, M. Baimukhanov Street, 45A, Atyrau 060027, Kazakhstan.
  • Department of Chemical & Biochemical Engineering, Satbayev University, 13 Satbayev Street, Almaty 050013, Kazakhstan.
  • Department of Chemistry and Chemical Technology, Kh. Dosmukhamedov Atyrau University, Studenchesky Ave., 1, Atyrau 060011, Kazakhstan.
  • A.V. Topchiev Institute of Petrochemical Synthesis Russian Academy of Sciences, Leninsky Prospekt, 29, Moscow 119991, Russia.
  • National Research Center "Kurchatov Institute", 1, Akademika Kurchatova Pl., Moscow 123182, Russia.

ORCID-Profile: Rinat M Iskakov, Fazilat B Kairliyeva, Ivan M Obidin, Mikhail S Kuzin, Timofey D Patsaev, Pavel S Gerasimenko, Igor S Makarov, Ivan Yu Skvortsov

Förderung

  • A.V. Topchiev Institute of Petrochemical Synthesis
  • Kurchatov Institute
  • State Program of TIPS RAS
  • NRC “Kurchatov institute”

Zitieren

APA

Iskakov, R. M., Bukanova, A. S., Kalauova, A. S., Kairliyeva, F. B., Nauashev, A. N., Shambilova, G. K., Obidin, I. M., Kuzin, M. S., Chernenko, D. N., Patsaev, T. D., Gerasimenko, P. S., Makarov, I. S., & Skvortsov, I. Y. (2025). Eco-Friendly Polypropylene Composites Reinforced with Cellulose Fibers and Silica Nanoparticles. Polymers, 17(10), 1290. https://doi.org/10.3390/polym17101290

Vancouver

Iskakov RM, Bukanova AS, Kalauova AS, Kairliyeva FB, Nauashev AN, Shambilova GK, et al. Eco-Friendly Polypropylene Composites Reinforced with Cellulose Fibers and Silica Nanoparticles. Polymers. 2025;17(10):1290. doi:10.3390/polym17101290

BibTeX
@article{Iskakov2025,
  author = {Iskakov, Rinat M and Bukanova, Aigul S and Kalauova, Altynay S and Kairliyeva, Fazilat B and Nauashev, Alimzhan N and Shambilova, Gulbarshin K and Obidin, Ivan M and Kuzin, Mikhail S and Chernenko, Dmitryi N and Patsaev, Timofey D and Gerasimenko, Pavel S and Makarov, Igor S and Skvortsov, Ivan Yu},
  title = {Eco-Friendly Polypropylene Composites Reinforced with Cellulose Fibers and Silica Nanoparticles},
  journal = {Polymers},
  year = {2025},
  volume = {17},
  number = {10},
  pages = {1290},
  doi = {10.3390/polym17101290}
}
Kostenlos starten →