Mechanical and Solvothermal Recycling of End-of-Life Carbon Fibre-Reinforced Plastic Products: Process Feasibility and Flexural Performance of Recycled Composites
Polymers · 25.03.2025 · 17 (7) · 878
DOI: 10.3390/polym17070878 ↗Kurz gefasst
Fachartikel in der Zeitschrift Polymers, online erschienen am 25.03.2025. Verfasst von Dario De Fazio und 6 weiteren Autor:innen. Beteiligte Einrichtung: Department of Chemical, Materials and Production Engineering, University of Naples "Federico II", P.le Tecchio 80, 80125 Naples, Italy. Die Arbeit wurde bisher 11-mal zitiert (Crossref) und nennt 64 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).
Abstract (Originalsprache)
The increasing demand for high-performance materials has led to an increase in the use of carbon fibre-reinforced plastics (CFRPs) in recent decades, increasing the waste from end-of-life materials and off-cuts. The recycling of CFRPs, especially when thermosetting matrices are used, still remains an open challenge for academia and industry, with chemical, thermal and mechanical strategies being explored. Among them, mechanical methods have garnered growing interest since they do not require high specific energy consumption or expensive apparatus. However, from the literature it was observed that when using these methods, traces of old matrix remain on the fibre’s surface, compromising the fibre–matrix adhesion efficiency and limiting their use in recycled composites. On the other hand, solvothermal methods are known for their high matrix dissolution efficiency that in turn improves the fibre–matrix adhesion. Therefore, in this paper, end-of-life CFRPs from the aeronautic sector were machined using a milling-based mechanical recycling method, while to remove the residual matrix from the fibre surface, the recovered chips were chemically treated with a two-step treatment at low temperature. Then, two types of recycled composite laminates were manufactured using the compression moulding technique: the first using recycled fibres only from the mechanical recycled method, and the second one using recycled fibres deriving from both recycling methods. The feasibility of the process was analysed observing that the additional chemical treatment led to a mass loss of almost 24% in the recycled fibres. FTIR analysis revealed the complete matrix dissolution since no spectra of epoxy resin groups were detected. Finally, the flexural behaviour of the recycled composites was investigated, revealing an increase in the flexural strength and modulus of the second sample typology, respectively, of almost 42% and 76% thanks to the improved fibre–matrix adhesion as a consequence of the solvothermal treatment.
Schlagwörter
Stichwörter der Autor:innen
Autor:innen und Institutionen
- Department of Chemical, Materials and Production Engineering, University of Naples "Federico II", P.le Tecchio 80, 80125 Naples, Italy.
ORCID-Profile: Dario De Fazio, Luca Boccarusso, Antonio Formisano, Giuseppina Luciani, Francesco Branda
Zitieren
APA
De Fazio, D., Boccarusso, L., Formisano, A., Grappa, R., Luciani, G., Branda, F., & Durante, M. (2025). Mechanical and Solvothermal Recycling of End-of-Life Carbon Fibre-Reinforced Plastic Products: Process Feasibility and Flexural Performance of Recycled Composites. Polymers, 17(7), 878. https://doi.org/10.3390/polym17070878
Vancouver
De Fazio D, Boccarusso L, Formisano A, Grappa R, Luciani G, Branda F, et al. Mechanical and Solvothermal Recycling of End-of-Life Carbon Fibre-Reinforced Plastic Products: Process Feasibility and Flexural Performance of Recycled Composites. Polymers. 2025;17(7):878. doi:10.3390/polym17070878
BibTeX
@article{DeFazio2025,
author = {De Fazio, Dario and Boccarusso, Luca and Formisano, Antonio and Grappa, Rossella and Luciani, Giuseppina and Branda, Francesco and Durante, Massimo},
title = {Mechanical and Solvothermal Recycling of End-of-Life Carbon Fibre-Reinforced Plastic Products: Process Feasibility and Flexural Performance of Recycled Composites},
journal = {Polymers},
year = {2025},
volume = {17},
number = {7},
pages = {878},
doi = {10.3390/polym17070878}
}
EUVIMED