Defect Passivation in Perovskite Solar Cells Using Polysuccinimide-Based Green Polymer Additives
Polymers · 28.02.2025 · 17 (5) · 653
DOI: 10.3390/polym17050653 ↗Kurz gefasst
Fachartikel in der Zeitschrift Polymers, online erschienen am 28.02.2025. Verfasst von Sergey S Kozlov und 7 weiteren Autor:innen. Beteiligte Einrichtung: Emanuel Institute of Biochemical Physics, Russian Academy of Sciences, 119334 Moscow, Russia. Die Arbeit wurde bisher 14-mal zitiert (Crossref) und nennt 58 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: This work was financially supported by the Ministry of Science and Higher Education of the Rus-sian Federation, topic № 45.9. "Theoretical and experimental stu…, Ministry of Science and Higher Education of the Russian Federation.
Abstract (Originalsprache)
Controlling traps and structural defects in perovskite absorber layers is crucial for enhancing both the device efficiency and long-term stability of perovskite solar cells (PSCs). Here we demonstrate the modification of perovskite films by introducing low-cost green polymers, polysuccinimide (PSI) and polyasparagine (PASP), into the perovskite layer. Structural, morphological and optoelectronic properties of polymer-modified perovskite films were probed by scanning electron microscopy (SEM), X-ray diffraction (XRD), Fourier transform infrared (FTIR) and UV-Vis spectroscopy. The incorporation of PSI triggers interactions between the polymer and perovskite, leading to the passivation of surface defects at the grain boundaries and improved morphology of perovskite films. This defect passivation boosted PSC performance, providing power conversion efficiency (PCE) values up to 20.1%. An optimal polymer concentration of 0.1 mg/mL in the perovskite precursor solution was identified for an improvement in the photovoltaic performance. It was shown that the primary factor leading to the observed enhancement in the power conversion efficiency for PSI-modified PSCs is the increase in the lifetime of charge carriers due to the efficient passivation of surface defects and suppression of recombination losses. Additionally, PSI-modified PSCs demonstrated enhanced stability, retaining over 80% of their initial efficiency after 40 days of storage under ambient conditions without encapsulation. The obtained results highlight the effectiveness of green polymer additives in passivating surface defects in perovskite films and provide a viable approach for improving the stability and performance of perovskite solar cells.
Schlagwörter
Stichwörter der Autor:innen
Autor:innen und Institutionen
- Emanuel Institute of Biochemical Physics, Russian Academy of Sciences, 119334 Moscow, Russia.
- N.N. Semenov Federal Research Center for Chemical Physics, Russian Academy of Sciences, 119991 Moscow, Russia.
ORCID-Profile: Sergey S Kozlov, Olga V Alexeeva, Alexey L Iordanskii
Förderung
- This work was financially supported by the Ministry of Science and Higher Education of the Rus-sian Federation, topic № 45.9. "Theoretical and experimental stu…
- Ministry of Science and Higher Education of the Russian Federation
Zitieren
APA
Kozlov, S. S., Alexeeva, O. V., Nikolskaia, A. B., Petrova, V. I., Karyagina, O. K., Iordanskii, A. L., Larina, L. L., & Shevaleevskiy, O. I. (2025). Defect Passivation in Perovskite Solar Cells Using Polysuccinimide-Based Green Polymer Additives. Polymers, 17(5), 653. https://doi.org/10.3390/polym17050653
Vancouver
Kozlov SS, Alexeeva OV, Nikolskaia AB, Petrova VI, Karyagina OK, Iordanskii AL, et al. Defect Passivation in Perovskite Solar Cells Using Polysuccinimide-Based Green Polymer Additives. Polymers. 2025;17(5):653. doi:10.3390/polym17050653
BibTeX
@article{Kozlov2025,
author = {Kozlov, Sergey S and Alexeeva, Olga V and Nikolskaia, Anna B and Petrova, Vasilisa I and Karyagina, Olga K and Iordanskii, Alexey L and Larina, Liudmila L and Shevaleevskiy, Oleg I},
title = {Defect Passivation in Perovskite Solar Cells Using Polysuccinimide-Based Green Polymer Additives},
journal = {Polymers},
year = {2025},
volume = {17},
number = {5},
pages = {653},
doi = {10.3390/polym17050653}
}
EUVIMED