EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Optimization of Process Parameters for Steel Wire-Reinforced Polylactic Acid Composites Produced by Additive Manufacturing

Turker Turkoglu iD, Ahmet Cagri Kilinc iD

Polymers · 26.02.2025 · 17 (5) · 624

DOI: 10.3390/polym17050624 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Polymers, online erschienen am 26.02.2025. Verfasst von Turker Turkoglu und 1 weiteren Autor:innen. Beteiligte Einrichtung: Department of Mechanical Engineering, Balıkesir University, Balıkesir 10145, Turkey. Die Arbeit wurde bisher 15-mal zitiert (Crossref) und nennt 45 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

The mechanical performance of Fused Deposition Modeling (FDM)-produced polymer composites is highly dependent on processing parameters; however, most studies focus on unreinforced polymers, leaving a gap in understanding how these parameters influence continuous wire-reinforced composites. This study addresses this gap by investigating the effect of hatch spacing and layer thickness on the tensile properties of steel wire-reinforced PLA composites. The Taguchi method was employed to systematically optimize mechanical performance, using an L9 orthogonal array to evaluate tensile strength across different process conditions. The results showed that layer thickness was the most influential factor, contributing to 75.861% of the total variance (F = 60.90, p = 0.001), followed by hatch spacing (21.647%, F = 17.37, p = 0.010). The highest tensile strength of 231.61 MPa was obtained at a hatch spacing of 0.4 mm and a layer thickness of 0.2 mm, confirming the importance of optimizing these parameters to improve interfacial bonding and minimize defects. Signal-to-Noise (S/N) ratio analysis further validated these optimal conditions, with the highest S/N ratio of 47.29 observed under the same settings. This study provides a structured approach to optimizing process parameters for metal-reinforced polymer composites, contributing to the development of stronger, more reliable FDM-produced composite materials.

Schlagwörter

Stichwörter der Autor:innen

additive manufacturingcharacterizationcompositescontinuous fiberdesign of experimentmechanical properties

Autor:innen und Institutionen

  • Department of Mechanical Engineering, Balıkesir University, Balıkesir 10145, Turkey.
  • Department of Mechanical Engineering, Osmaniye Korkut Ata University, Osmaniye 80010, Turkey.

ORCID-Profile: Turker Turkoglu, Ahmet Cagri Kilinc

Zitieren

APA

Turkoglu, T., & Kilinc, A. C. (2025). Optimization of Process Parameters for Steel Wire-Reinforced Polylactic Acid Composites Produced by Additive Manufacturing. Polymers, 17(5), 624. https://doi.org/10.3390/polym17050624

Vancouver

Turkoglu T, Kilinc AC. Optimization of Process Parameters for Steel Wire-Reinforced Polylactic Acid Composites Produced by Additive Manufacturing. Polymers. 2025;17(5):624. doi:10.3390/polym17050624

BibTeX
@article{Turkoglu2025,
  author = {Turkoglu, Turker and Kilinc, Ahmet Cagri},
  title = {Optimization of Process Parameters for Steel Wire-Reinforced Polylactic Acid Composites Produced by Additive Manufacturing},
  journal = {Polymers},
  year = {2025},
  volume = {17},
  number = {5},
  pages = {624},
  doi = {10.3390/polym17050624}
}
Kostenlos starten →