EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Fatigue Behaviour of PA66 GF30 at Different Temperatures

Marko Zadravec, Janez Kramberger iD, Branko Nečemer iD, Srečko Glodež iD

Polymers · 27.12.2024 · 17 (1) · 42

DOI: 10.3390/polym17010042 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Polymers, online erschienen am 27.12.2024. Verfasst von Marko Zadravec und 3 weiteren Autor:innen. Beteiligte Einrichtung: Faculty of Mechanical Engineering, University of Maribor, Smetanova 17, 2000 Maribor, Slovenia. Die Arbeit wurde bisher 5-mal zitiert (Crossref) und nennt 42 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: The Slovenian Research and Innovation Agency, the Research Core Funding, the Basic Postdoc Research Project.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

A comprehensive experimental investigation to understand the mechanical properties and fatigue behaviour of glass-reinforced polyamide (PA66 GF30) at different temperatures is presented in this paper. The specimens for quasi-static and fatigue testing were machined from previously extruded plates, where two orientations were considered: (i) the extrusion direction (ED) and (ii) the direction perpendicular to extrusion (PED). Both the quasi-static and fatigue tests were performed under different temperatures (22 °C and 100 °C). The fatigue tests were performed in a load control regime under pulsating loading (R = 0.1) to create S–N curves for all the temperatures and loading directions. The experimental results of the quasi-static tests showed that the test specimens manufactured in the extrusion direction have better mechanical properties when compared to those of the specimens manufactured perpendicular to the extrusion direction. Furthermore, the analysis of the quasi-static tensile test results showed that tensile strength, yield strength, and the modulus of elasticity are significantly dependent on the temperature and deteriorate when the temperature is increased from 22 °C to 100 °C. The results of the fatigue tests showed that at both the temperatures (22 °C and 100 °C), the samples produced in the direction of extrusion exhibited higher fatigue strength than those produced perpendicular to the direction of extrusion. For all the sample orientations, the fatigue strength decreased significantly with increasing temperature. The obtained experimental results could be very useful when designing and dimensioning different dynamically loaded engineering components made of PA66 GF30 subjected to high temperatures.

Schlagwörter

Stichwörter der Autor:innen

PA66 GF30experimental testingfatigueincreased temperatures

Autor:innen und Institutionen

  • Faculty of Mechanical Engineering, University of Maribor, Smetanova 17, 2000 Maribor, Slovenia.

ORCID-Profile: Janez Kramberger, Branko Nečemer, Srečko Glodež

Förderung

  • The Slovenian Research and Innovation Agency
  • the Research Core Funding
  • the Basic Postdoc Research Project
  • the Slovenian Research Agency

Zitieren

APA

Zadravec, M., Kramberger, J., Nečemer, B., & Glodež, S. (2024). Fatigue Behaviour of PA66 GF30 at Different Temperatures. Polymers, 17(1), 42. https://doi.org/10.3390/polym17010042

Vancouver

Zadravec M, Kramberger J, Nečemer B, Glodež S. Fatigue Behaviour of PA66 GF30 at Different Temperatures. Polymers. 2024;17(1):42. doi:10.3390/polym17010042

BibTeX
@article{Zadravec2024,
  author = {Zadravec, Marko and Kramberger, Janez and Nečemer, Branko and Glodež, Srečko},
  title = {Fatigue Behaviour of PA66 GF30 at Different Temperatures},
  journal = {Polymers},
  year = {2024},
  volume = {17},
  number = {1},
  pages = {42},
  doi = {10.3390/polym17010042}
}
Kostenlos starten →