EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

3D Printing of Continuous Basalt Fiber-Reinforced Composites: Characterization of the In-Plane Mechanical Properties and Anisotropy Evaluation

Marco Zanelli, Giulia Ronconi, Nicola Pritoni, Andrea D'Iorio iD, Monica Bertoldo iD, Valentina Mazzanti iD, Francesco Mollica iD

Polymers · 30.11.2024 · 16 (23) · 3377

DOI: 10.3390/polym16233377 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Polymers, online erschienen am 30.11.2024. Verfasst von Marco Zanelli und 6 weiteren Autor:innen. Beteiligte Einrichtung: Department of Engineering, University of Ferrara, Via Saragat 1, 44122 Ferrara, Italy. Die Arbeit wurde bisher 17-mal zitiert (Crossref) und nennt 39 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Usage of continuous fibers as a reinforcement would definitely increase the mechanical properties of 3D-printed materials. The result is a continuous fiber-reinforced composite obtained by additive manufacturing that is not limited to prototyping or non-structural applications. Among the available continuous reinforcing fibers, basalt has not been extensively studied in 3D printing. This material is attractive due to its natural origin, good mechanical properties, impact strength, and high chemical and thermal resistance. In this work, a continuous basalt fiber co-extruded composite obtained by fused filament fabrication was characterized both thermally and mechanically, concerning the in-plane tensile properties. The degree of anisotropy of the material was also assessed, both qualitatively and quantitatively. The 3D-printed composite showed longitudinal properties, which were 15 times higher than the pure matrix, thus meeting structural requirements. On the other hand, transverse and shear properties were much lower than longitudinal ones, thus leading to a strongly anisotropic material. This was also confirmed by the anisotropy evaluation that was performed numerically and graphically using an innovative approach. This behavior affects the design of 3D-printed parts; thus, an optimized continuous fiber deposition is necessary for structural applications.

Schlagwörter

Stichwörter der Autor:innen

Anisoprint ComposerPolyamide 12co-extruded continuous fiberfused deposition modelingnatural fiber

Autor:innen und Institutionen

  • Department of Engineering, University of Ferrara, Via Saragat 1, 44122 Ferrara, Italy.
  • Department of Chemical, Pharmaceutical and Agricultural Sciences, University of Ferrara, Via L. Borsari 46, 44121 Ferrara, Italy.

ORCID-Profile: Andrea D'Iorio, Monica Bertoldo, Valentina Mazzanti, Francesco Mollica

Zitieren

APA

Zanelli, M., Ronconi, G., Pritoni, N., D'Iorio, A., Bertoldo, M., Mazzanti, V., & Mollica, F. (2024). 3D Printing of Continuous Basalt Fiber-Reinforced Composites: Characterization of the In-Plane Mechanical Properties and Anisotropy Evaluation. Polymers, 16(23), 3377. https://doi.org/10.3390/polym16233377

Vancouver

Zanelli M, Ronconi G, Pritoni N, D'Iorio A, Bertoldo M, Mazzanti V, et al. 3D Printing of Continuous Basalt Fiber-Reinforced Composites: Characterization of the In-Plane Mechanical Properties and Anisotropy Evaluation. Polymers. 2024;16(23):3377. doi:10.3390/polym16233377

BibTeX
@article{Zanelli2024,
  author = {Zanelli, Marco and Ronconi, Giulia and Pritoni, Nicola and D'Iorio, Andrea and Bertoldo, Monica and Mazzanti, Valentina and Mollica, Francesco},
  title = {3D Printing of Continuous Basalt Fiber-Reinforced Composites: Characterization of the In-Plane Mechanical Properties and Anisotropy Evaluation},
  journal = {Polymers},
  year = {2024},
  volume = {16},
  number = {23},
  pages = {3377},
  doi = {10.3390/polym16233377}
}
Kostenlos starten →