Machining Eco-Friendly Jute Fiber-Reinforced Epoxy Composites Using Specially Produced Cryo-Treated and Untreated Cutting Tools
Polymers · 27.11.2024 · 16 (23) · 3329
DOI: 10.3390/polym16233329 ↗Kurz gefasst
Fachartikel in der Zeitschrift Polymers, online erschienen am 27.11.2024. Verfasst von Mehmet Şükrü Adin und 1 weiteren Autor:innen. Beteiligte Einrichtung: Besiri OSB Vocational School, Batman University, Batman 72060, Turkey. Die Arbeit wurde bisher 124-mal zitiert (Crossref) und nennt 50 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).
Abstract (Originalsprache)
In recent years, consumers have become increasingly interested in natural, biodegradable and eco-friendly composites. Eco-friendly composites manufactured using natural reinforcing filling materials stand out with properties such as cost effectiveness and easy accessibility. For these reasons, in this research, a composite workpiece was specially manufactured using eco-friendly jute fibers. Two cost-effective cutting tools were specially produced to ensure high-quality machining of this composite workpiece. One of these specially manufactured cutting tools was subjected to DC&T (deep cryogenic treatment and tempering) processes to improve its performance. At the end of the research, when the lowest and highest Fd (delamination factor) values obtained with DC&T-T1 and T1 cutting tools were compared, it was observed that 5.49% and 6.23% better results were obtained with the DC&T-T1 cutting tool, respectively. From the analysis of the S/N (signal-to-noise) ratios obtained using Fd values, it was found that the most appropriate machining parameters for the composite workpiece used in this investigation were the DC&T-T1 cutting tool, a 2000 rev/min spindle speed and a 100 mm/min feed rate. Through ANOVAs (analyses of variance), it was discovered that the most significant parameter having an impact on the Fd values was the spindle speed, with a rate of 53.01%. Considering the lowest and highest Ra (average surface roughness) values obtained using DC&T-T1 and T1 cutting tools, it was seen that 19.42% and 16.91% better results were obtained using the DC&T-T1 cutting tool, respectively. In the S/N ratio analysis results obtained using Ra values, it was revealed that the most appropriate machining parameters for the composite workpiece used in this investigation were the DC&T-T1 cutting tool, a 2000 rev/min spindle speed and a 100 mm/min feed rate. In the ANOVAs, it was revealed that the most significant parameter having an effect on the Ra values was the feed rate at 37.86%.
Schlagwörter
Stichwörter der Autor:innen
Autor:innen und Institutionen
- Besiri OSB Vocational School, Batman University, Batman 72060, Turkey.
- Faculty of Engineering and Architecture, Batman University, Batman 72100, Turkey.
ORCID-Profile: Mehmet Şükrü Adin, Hamit Adin
Zitieren
APA
Adin, M. Ş., & Adin, H. (2024). Machining Eco-Friendly Jute Fiber-Reinforced Epoxy Composites Using Specially Produced Cryo-Treated and Untreated Cutting Tools. Polymers, 16(23), 3329. https://doi.org/10.3390/polym16233329
Vancouver
Adin MŞ, Adin H. Machining Eco-Friendly Jute Fiber-Reinforced Epoxy Composites Using Specially Produced Cryo-Treated and Untreated Cutting Tools. Polymers. 2024;16(23):3329. doi:10.3390/polym16233329
BibTeX
@article{Adin2024,
author = {Adin, Mehmet Şükrü and Adin, Hamit},
title = {Machining Eco-Friendly Jute Fiber-Reinforced Epoxy Composites Using Specially Produced Cryo-Treated and Untreated Cutting Tools},
journal = {Polymers},
year = {2024},
volume = {16},
number = {23},
pages = {3329},
doi = {10.3390/polym16233329}
}
EUVIMED