EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Wear and Dynamic Mechanical Analysis (DMA) of Samples Produced via Fused Deposition Modelling (FDM) 3D Printing Method

Jiri Struz iD, Miroslav Trochta iD, Lukas Hruzik iD, Daniel Pistacek iD, Sylwester Stawarz iD, Wojciech Kucharczyk iD, Miroslaw Rucki iD

Polymers · 28.10.2024 · 16 (21) · 3018

DOI: 10.3390/polym16213018 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Polymers, online erschienen am 28.10.2024. Verfasst von Jiri Struz und 6 weiteren Autor:innen. Beteiligte Einrichtung: Faculty of Mechanical Engineering, VSB-Technical University of Ostrava, 17. Listopadu 2172/15, 70800 Ostrava, Czech Republic. Die Arbeit wurde bisher 18-mal zitiert (Crossref) und nennt 56 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Ministry of education, youth and sports of the Czech Republic, MINISTRY OF EDUCATION, YOUTH AND SPORTS.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

In recent years, plastic and metal 3D printing has experienced massive development in the professional and hobby spheres, especially for rapid prototyping, reverse engineering, maintenance and quick repairs. However, this technology is limited by a number of factors, with the most common being the cost and availability of the technology but also the lack of information on material properties. This study focuses on investigating the material properties of PLA, PETG, HIPS, PA, ABS and ASA in order to elucidate their behavior in terms of wear and thermal resistance. The research builds on previous studies focusing on the mechanical properties of these materials and includes wear testing and DMA analysis. Weight loss, frictional forces, and frictional work including relative frictional work are recorded as part of this testing. The storage modulus and loss modulus including tan(δ) were then measured using DMA.

Schlagwörter

Stichwörter der Autor:innen

DMAFDMcoefficient of frictionglass transition temperatureloss modulusstorage modulusweight loss

Autor:innen und Institutionen

  • Faculty of Mechanical Engineering, VSB-Technical University of Ostrava, 17. Listopadu 2172/15, 70800 Ostrava, Czech Republic.
  • Faculty of Mechanical Engineering, Casimir Pulaski Radom University, Stasiecki Str. 54, 26-600 Radom, Poland.
  • Institute of Mechanical Science, Vilnius Gediminas Technical University, J. Basanaviciaus Str. 28, LT-03224 Vilnius, Lithuania.

ORCID-Profile: Jiri Struz, Miroslav Trochta, Lukas Hruzik, Daniel Pistacek, Sylwester Stawarz, Wojciech Kucharczyk, Miroslaw Rucki

Förderung

  • Ministry of education, youth and sports of the Czech Republic
  • MINISTRY OF EDUCATION, YOUTH AND SPORTS

Zitieren

APA

Struz, J., Trochta, M., Hruzik, L., Pistacek, D., Stawarz, S., Kucharczyk, W., & Rucki, M. (2024). Wear and Dynamic Mechanical Analysis (DMA) of Samples Produced via Fused Deposition Modelling (FDM) 3D Printing Method. Polymers, 16(21), 3018. https://doi.org/10.3390/polym16213018

Vancouver

Struz J, Trochta M, Hruzik L, Pistacek D, Stawarz S, Kucharczyk W, et al. Wear and Dynamic Mechanical Analysis (DMA) of Samples Produced via Fused Deposition Modelling (FDM) 3D Printing Method. Polymers. 2024;16(21):3018. doi:10.3390/polym16213018

BibTeX
@article{Struz2024,
  author = {Struz, Jiri and Trochta, Miroslav and Hruzik, Lukas and Pistacek, Daniel and Stawarz, Sylwester and Kucharczyk, Wojciech and Rucki, Miroslaw},
  title = {Wear and Dynamic Mechanical Analysis (DMA) of Samples Produced via Fused Deposition Modelling (FDM) 3D Printing Method},
  journal = {Polymers},
  year = {2024},
  volume = {16},
  number = {21},
  pages = {3018},
  doi = {10.3390/polym16213018}
}
Kostenlos starten →