EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Synergistic Reinforcing Effect of Hazelnut Shells and Hydrotalcite on Properties of Rigid Polyurethane Foam Composites

Sylwia Makowska, Karolina Miedzińska iD, Agnė Kairytė iD, Krzysztof Strzelec iD

Polymers · 23.10.2024 · 16 (21) · 2968

DOI: 10.3390/polym16212968 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Polymers, online erschienen am 23.10.2024. Verfasst von Sylwia Makowska und 3 weiteren Autor:innen. Beteiligte Einrichtung: Institute of Polymer and Dye Technology, Lodz University of Technology, 90-924 Lodz, Poland. Die Arbeit wurde bisher 4-mal zitiert (Crossref) und nennt 79 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Civil Engineering Research Centre.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Recently, the development of composite materials from agricultural and forestry waste has become an attractive area of research. The use of bio-waste is beneficial for economic and environmental reasons, adapting it to cost effectiveness and environmental sustainability. In the presented study, the possibility of using hazelnut shell (HS) and hydrotalcite (HT) mineral filler was investigated. The effects of fillers in the amount of 10 wt.% on selected properties of polyurethane composites, such as rheological properties (dynamic viscosity, processing times), mechanical properties (compressive strength, flexural strength, hardness), insulating properties (thermal conductivity), and flame-retardant properties (e.g., ignition time, limiting oxygen index, peak heat release), were investigated. Polyurethane foams containing fillers have been shown to have better performance properties compared to unmodified polyurethane foams. For example, the addition of 10 wt% of hydrotalcite filler leads to PU composite foams with improved compression strength (improvement by ~20%), higher flexural strength (increase of ~38%), and comparable thermal conductivity (0.03055 W m–1 K–1 at 20 °C). Moreover, the incorporation of organic fillers has a positive effect on the fire resistance of PU materials. For example, the results from the cone calorimeter test showed that the incorporation of 10 wt% of hydrotalcite filler significantly reduced the peak of the heat release rate (pHRR) by ca. 30% compared with that of unmodified PU foam, and increased the value of the limiting oxygen index from 19.8% to 21.7%.

Schlagwörter

Stichwörter der Autor:innen

flame-retardant propertieshazelnut shellshydrotalcitemechanical propertiespolyurethane

Autor:innen und Institutionen

  • Institute of Polymer and Dye Technology, Lodz University of Technology, 90-924 Lodz, Poland.
  • Civil Engineering Research Centre, Vilnius Gediminas Technical University, Saulėtekio Av. 11, LT-10223 Vilnius, Lithuania.
  • Laboratory of Thermal Insulating Materials and Acoustics, Faculty of Civil Engineering, Institute of Building Materials, Vilnius Gediminas Technical University, Linkmenu St. 28, LT-08217 Vilnius, Lithuania.

ORCID-Profile: Karolina Miedzińska, Agnė Kairytė, Krzysztof Strzelec

Förderung

  • Civil Engineering Research Centre

Zitieren

APA

Makowska, S., Miedzińska, K., Kairytė, A., & Strzelec, K. (2024). Synergistic Reinforcing Effect of Hazelnut Shells and Hydrotalcite on Properties of Rigid Polyurethane Foam Composites. Polymers, 16(21), 2968. https://doi.org/10.3390/polym16212968

Vancouver

Makowska S, Miedzińska K, Kairytė A, Strzelec K. Synergistic Reinforcing Effect of Hazelnut Shells and Hydrotalcite on Properties of Rigid Polyurethane Foam Composites. Polymers. 2024;16(21):2968. doi:10.3390/polym16212968

BibTeX
@article{Makowska2024,
  author = {Makowska, Sylwia and Miedzińska, Karolina and Kairytė, Agnė and Strzelec, Krzysztof},
  title = {Synergistic Reinforcing Effect of Hazelnut Shells and Hydrotalcite on Properties of Rigid Polyurethane Foam Composites},
  journal = {Polymers},
  year = {2024},
  volume = {16},
  number = {21},
  pages = {2968},
  doi = {10.3390/polym16212968}
}
Kostenlos starten →