Comparison of Bulk Polymeric Resin Composite and Hybrid Glass Ionomer Cement in Adhesive Class I Dental Restorations: A 3D Finite Element Analysis
Polymers · 05.09.2024 · 16 (17) · 2525
DOI: 10.3390/polym16172525 ↗Kurz gefasst
Fachartikel in der Zeitschrift Polymers, online erschienen am 05.09.2024. Verfasst von Alessandro E di Lauro und 4 weiteren Autor:innen. Beteiligte Einrichtung: Department of Neurosciences, Reproductive Sciences and Odontostomatological Sciences, University of Naples Federico II, 80131 Naples, Italy. Die Arbeit wurde bisher 16-mal zitiert (Crossref) und nennt 40 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).
Abstract (Originalsprache)
This study aimed to investigate the mechanical behavior of resin composites and hybrid glass ionomer cement in class I adhesive dental restorations under loading and shrinkage conditions. Three CAD models of a mandibular first molar with class I cavities were created and restored with different techniques: a bi-layer of Equia Forte HT with Filtek One Bulk Fill Restorative composite (model A), a single layer of adhesive and Filtek One Bulk Fill Restorative (model B), and a single layer of Equia forte HT (model C). Each model was exported to computer-aided engineering software, and 3D finite element models were created. Models A and B exhibited a similar pattern of stress distribution along the enamel–restoration interface, with stress peaks of 12.5 MPa and 14 MPa observed in the enamel tissue. The sound tooth, B, and C models showed a similar trend along the interface between dentine and restoration. A stress peak of about 0.5 MPa was detected in the enamel of both the sound tooth and B models. Model C showed a reduced stress peak of about 1.2 MPa. A significant stress reduction in 4 mm deep class I cavities in lower molars was observed in models where non-shrinking dental filling materials, like the hybrid glass ionomer cement used in model C, were applied. Stress reduction was also achieved in model A, which employed a bi-layer technique with a shrinking polymeric filling material (bulk resin composite). Model C’s performance closely resembled that of a sound tooth.
Schlagwörter
Stichwörter der Autor:innen
Autor:innen und Institutionen
- Department of Neurosciences, Reproductive Sciences and Odontostomatological Sciences, University of Naples Federico II, 80131 Naples, Italy.
- Department of Reconstructive Oral Care, Academic Centre for Dentistry Amsterdam (ACTA), Universiteit van Amsterdam and Vrije Universiteit Amsterdam, 1081 LA Amsterdam, The Netherlands.
ORCID-Profile: João P Mendes Tribst, Pietro Ausiello
Zitieren
APA
di Lauro, A. E., Ciaramella, S., Tribst, J. P. M., Aliberti, A., & Ausiello, P. (2024). Comparison of Bulk Polymeric Resin Composite and Hybrid Glass Ionomer Cement in Adhesive Class I Dental Restorations: A 3D Finite Element Analysis. Polymers, 16(17), 2525. https://doi.org/10.3390/polym16172525
Vancouver
di Lauro AE, Ciaramella S, Tribst JPM, Aliberti A, Ausiello P. Comparison of Bulk Polymeric Resin Composite and Hybrid Glass Ionomer Cement in Adhesive Class I Dental Restorations: A 3D Finite Element Analysis. Polymers. 2024;16(17):2525. doi:10.3390/polym16172525
BibTeX
@article{diLauro2024,
author = {di Lauro, Alessandro E and Ciaramella, Stefano and Tribst, João P Mendes and Aliberti, Angelo and Ausiello, Pietro},
title = {Comparison of Bulk Polymeric Resin Composite and Hybrid Glass Ionomer Cement in Adhesive Class I Dental Restorations: A 3D Finite Element Analysis},
journal = {Polymers},
year = {2024},
volume = {16},
number = {17},
pages = {2525},
doi = {10.3390/polym16172525}
}
EUVIMED