EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

3D-Printed Hydrogels as Photothermal Actuators

Melanie M Ghelardini, Martin Geisler iD, Niclas Weigel, Jameson P Hankwitz, Nicolas Hauck, Jonas Schubert iD, Andreas Fery iD, Joseph B Tracy iD, Julian Thiele

Polymers · 17.07.2024 · 16 (14) · 2032

DOI: 10.3390/polym16142032 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Polymers, online erschienen am 17.07.2024. Verfasst von Melanie M Ghelardini und 8 weiteren Autor:innen. Beteiligte Einrichtung: Department of Materials Science and Engineering, North Carolina State University, Raleigh, NC 27695, USA. Die Arbeit wurde bisher 9-mal zitiert (Crossref) und nennt 78 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: National Science Foundation, German Research Foundation, European Union Horizon 2020.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Thermoresponsive hydrogels were 3D-printed with embedded gold nanorods (GNRs), which enable shape change through photothermal heating. GNRs were functionalized with bovine serum albumin and mixed with a photosensitizer and poly(N-isopropylacrylamide) (PNIPAAm) macromer, forming an ink for 3D printing by direct ink writing. A macromer-based approach was chosen to provide good microstructural homogeneity and optical transparency of the unloaded hydrogel in its swollen state. The ink was printed into an acetylated gelatin hydrogel support matrix to prevent the spreading of the low-viscosity ink and provide mechanical stability during printing and concurrent photocrosslinking. Acetylated gelatin hydrogel was introduced because it allows for melting and removal of the support structure below the transition temperature of the crosslinked PNIPAAm structure. Convective and photothermal heating were compared, which both triggered the phase transition of PNIPAAm and induced reversible shrinkage of the hydrogel–GNR composite for a range of GNR loadings. During reswelling after photothermal heating, some structures formed an internally buckled state, where minor mechanical agitation recovered the unbuckled structure. The BSA-GNRs did not leach out of the structure during multiple cycles of shrinkage and reswelling. This work demonstrates the promise of 3D-printed, photoresponsive structures as hydrogel actuators.

Schlagwörter

Stichwörter der Autor:innen

3D printingbioplottingcycloadditiongelatingold nanorodsphotothermal heatingpoly(N-isopropylacrylamide)

Autor:innen und Institutionen

  • Department of Materials Science and Engineering, North Carolina State University, Raleigh, NC 27695, USA.
  • Leibniz Institute of Polymer Research Dresden, Institute of Physical Chemistry and Polymer Physics, 01069 Dresden, Germany.
  • Institute of Physical Chemistry and Polymer Physics, Technische Universität Dresden, 01062 Dresden, Germany.
  • Institute of Chemistry, Otto von Guericke University Magdeburg, Universitätsplatz 2, 39106 Magdeburg, Germany.

ORCID-Profile: Martin Geisler, Jonas Schubert, Andreas Fery, Joseph B Tracy

Förderung

  • National Science Foundation
  • German Research Foundation
  • European Union Horizon 2020
  • Analytical Instrumentation Facility (AIF) at North Carolina State University
  • Alexander von Humboldt Foundation
  • Dresden Center for Intelligent Materials (DCIM)
  • European Research Council (ERC)
  • State of North Carolina and the National Science Foundation

Zitieren

APA

Ghelardini, M. M., Geisler, M., Weigel, N., Hankwitz, J. P., Hauck, N., Schubert, J., Fery, A., Tracy, J. B., & Thiele, J. (2024). 3D-Printed Hydrogels as Photothermal Actuators. Polymers, 16(14), 2032. https://doi.org/10.3390/polym16142032

Vancouver

Ghelardini MM, Geisler M, Weigel N, Hankwitz JP, Hauck N, Schubert J, et al. 3D-Printed Hydrogels as Photothermal Actuators. Polymers. 2024;16(14):2032. doi:10.3390/polym16142032

BibTeX
@article{Ghelardini2024,
  author = {Ghelardini, Melanie M and Geisler, Martin and Weigel, Niclas and Hankwitz, Jameson P and Hauck, Nicolas and Schubert, Jonas and Fery, Andreas and Tracy, Joseph B and Thiele, Julian},
  title = {3D-Printed Hydrogels as Photothermal Actuators},
  journal = {Polymers},
  year = {2024},
  volume = {16},
  number = {14},
  pages = {2032},
  doi = {10.3390/polym16142032}
}
Kostenlos starten →