EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Variations in the Thermomechanical and Structural Properties during the Cooling of Shape-Memory R-PETG

Ștefan-Dumitru Sava, Bogdan Pricop iD, Radu-Ioachim Comăneci, Nicanor Cimpoeșu, Mihai Popa iD, Nicoleta-Monica Lohan iD, Leandru-Gheorghe Bujoreanu iD

Polymers · 09.07.2024 · 16 (14) · 1965

DOI: 10.3390/polym16141965 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Polymers, online erschienen am 09.07.2024. Verfasst von Ștefan-Dumitru Sava und 6 weiteren Autor:innen. Beteiligte Einrichtung: Faculty of Materials Science, "Gheorghe Asachi" Technical University of Iași, Blvd. Dimitrie Mangeron 71A, 700050 Iasi, Romania. Die Arbeit wurde bisher 5-mal zitiert (Crossref) und nennt 46 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

One of the useful features of 3D-printed specimens of recycled polyethylene terephthalate glycol (R-PETG) is the ability to repetitively develop free recovery as well as the work-generating, shape-memory effect. This behavior is enabled by the R-PETG’s capacity to stiffen during cooling, thus allowing for a new temporary shape to be induced. Aiming to devise an explanation for the polymer’s stiffening, in this study, the variation in some of the R-PETG’s parameters during cooling are emphasized and discussed. The evolution of an R-PETG filament’s shape was monitored during room-temperature-bending heating–cooling cycles. Straight-shape recovery and the complete loss of stiffness were observed at the start and the end of heating, respectively, followed by the forced straightening of the filament, performed by the operator, around 40 °C, during cooling. The tests performed by dynamic mechanical analysis disclosed the rise of the storage modulus (E’) after 100 °C heating followed by either liquid-nitrogen- or air-cooling to room temperature, in such a way that E’ was always larger after cooling than initially. Static tests emphasized a peculiar stress variation during a heating–cooling cycle applied in air, within the heating chamber of the tensile testing machine. Tensile-failure tests were performed at −10 °C at a rate of 100 mm/min, with specimens printed at various deposition directions between 10 and 40° to the transversal direction. The specimens printed at 40°, which had the largest ultimate strains, were broken with tensile rates between 100 and 500 mm/min. Deformation rate increase favored the shift from crazing to delamination failure modes. The correlation between the structural changes, the sharp E’ increase on heating, and the stiffening induced by cooling represents a novel approach that enables the use of 3D-printed R-PETG for the fabrication of the active parts of low-priced lightweight resettable actuators.

Schlagwörter

Stichwörter der Autor:innen

3D printingbrittlenesscooling effectfractographsrecycled PETGshape-memory effectstorage modulustensile testingthermomechanical cycling

Autor:innen und Institutionen

  • Faculty of Materials Science, "Gheorghe Asachi" Technical University of Iași, Blvd. Dimitrie Mangeron 71A, 700050 Iasi, Romania.

ORCID-Profile: Bogdan Pricop, Mihai Popa, Nicoleta-Monica Lohan, Leandru-Gheorghe Bujoreanu

Zitieren

APA

Sava, Ș. D., Pricop, B., Comăneci, R. I., Cimpoeșu, N., Popa, M., Lohan, N. M., & Bujoreanu, L. G. (2024). Variations in the Thermomechanical and Structural Properties during the Cooling of Shape-Memory R-PETG. Polymers, 16(14), 1965. https://doi.org/10.3390/polym16141965

Vancouver

Sava ȘD, Pricop B, Comăneci RI, Cimpoeșu N, Popa M, Lohan NM, et al. Variations in the Thermomechanical and Structural Properties during the Cooling of Shape-Memory R-PETG. Polymers. 2024;16(14):1965. doi:10.3390/polym16141965

BibTeX
@article{Sava2024,
  author = {Sava, Ștefan-Dumitru and Pricop, Bogdan and Comăneci, Radu-Ioachim and Cimpoeșu, Nicanor and Popa, Mihai and Lohan, Nicoleta-Monica and Bujoreanu, Leandru-Gheorghe},
  title = {Variations in the Thermomechanical and Structural Properties during the Cooling of Shape-Memory R-PETG},
  journal = {Polymers},
  year = {2024},
  volume = {16},
  number = {14},
  pages = {1965},
  doi = {10.3390/polym16141965}
}
Kostenlos starten →