Improvements in Hydrolytic Stability of Alkali-Activated Mine Tailings via Addition of Sodium Silicate Activator
Polymers · 31.03.2024 · 16 (7) · 957
DOI: 10.3390/polym16070957 ↗Kurz gefasst
Fachartikel in der Zeitschrift Polymers, online erschienen am 31.03.2024. Verfasst von Cara Clements und 3 weiteren Autor:innen. Beteiligte Einrichtung: Department of Civil and Environmental Engineering, Colorado School of Mines, 1500 Illinois Street, Golden, CO 80401, USA. Die Arbeit wurde bisher 13-mal zitiert (Crossref) und nennt 78 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: National University of Saint Augustine, Universidad Nacional de San Agustín (UNSA).
Abstract (Originalsprache)
Over 14 billion tons of mine tailings are produced throughout the world each year, and this type of waste is generally stored onsite indefinitely. Alkali activation is a promising strategy for the reuse of mine tailings to produce construction materials, converting this waste stream into a value-added product. One major problem with alkali-activated mine tailings is their low durability in water (i.e., low hydrolytic stability). In this article, the influence of a mixed sodium hydroxide/sodium silicate alkali activator on the compressive strength, hydrolytic stability, and microstructure of alkali-activated materials (AAMs) were systematically investigated. XRD, FTIR, NMR, and NAD were used to investigate microstructural changes, and a water immersion test was used to show improvements in hydrolytic stability. For gold mine tailings activated with pure sodium hydroxide, the compressive strength was 15 MPa and a seven-day water immersion test caused a strength loss of 70%. With an addition of 1 M sodium silicate in the activator, the AAMs achieved a compressive strength of over 30 MPa and strength loss of only 45%. This paper proposes a mechanism explaining why the strength and hydrolytic stability of AAMs are dependent on the dosage of soluble silicate. A high dosage of sodium silicate inhibits the depolymerization of the source material, which results in a sample with less amorphous aluminosilicate gel and, therefore, lower hydrolytic stability.
Schlagwörter
Stichwörter der Autor:innen
Autor:innen und Institutionen
- Department of Civil and Environmental Engineering, Colorado School of Mines, 1500 Illinois Street, Golden, CO 80401, USA.
- Metallurgical Engineering Department, National University of San Agustin de Arequipa, Santa Cataline No. 117, Arequipa 04000, Peru.
ORCID-Profile: Cara Clements, Ahmadreza Hedayat
Förderung
- National University of Saint Augustine
- Universidad Nacional de San Agustín (UNSA)
Zitieren
APA
Clements, C., Tunstall, L., Bolanos Sosa, H. G., & Hedayat, A. (2024). Improvements in Hydrolytic Stability of Alkali-Activated Mine Tailings via Addition of Sodium Silicate Activator. Polymers, 16(7), 957. https://doi.org/10.3390/polym16070957
Vancouver
Clements C, Tunstall L, Bolanos Sosa HG, Hedayat A. Improvements in Hydrolytic Stability of Alkali-Activated Mine Tailings via Addition of Sodium Silicate Activator. Polymers. 2024;16(7):957. doi:10.3390/polym16070957
BibTeX
@article{Clements2024,
author = {Clements, Cara and Tunstall, Lori and Bolanos Sosa, Hector Gelber and Hedayat, Ahmadreza},
title = {Improvements in Hydrolytic Stability of Alkali-Activated Mine Tailings via Addition of Sodium Silicate Activator},
journal = {Polymers},
year = {2024},
volume = {16},
number = {7},
pages = {957},
doi = {10.3390/polym16070957}
}
EUVIMED