Performance of Particleboard Made of Agroforestry Residues Bonded with Thermosetting Adhesive Derived from Waste Styrofoam
Polymers · 17.02.2024 · 16 (4) · 543
DOI: 10.3390/polym16040543 ↗Kurz gefasst
Fachartikel in der Zeitschrift Polymers, online erschienen am 17.02.2024. Verfasst von Tati Karliati und 8 weiteren Autor:innen. Beteiligte Einrichtung: School of Life Sciences and Technology, Institut Teknologi Bandung, Bandung 40132, Indonesia. Die Arbeit wurde bisher 13-mal zitiert (Crossref) und nennt 43 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Bandung Institute of Technology, Research, Community Service and innovation program (PPMI) collaborative scheme, School of Life Sciences and Technology, Institut Teknologi Bandung.
Abstract (Originalsprache)
This paper investigated the upcycling process of thermoplastic waste polystyrene (WPS) into thermosetting particleboard adhesive using two cross-linkers, namely methylene diphenyl diisocyanate (MDI) and maleic anhydride (MA). The WPS was dissolved in an organic co-solvent. The weight ratio of WPS/co-solvent was 1:9, and 10% of cross-linkers based on the WPS solids content were added subsequently at 60 °C under continuous stirring for 30 min. The adhesive properties, cohesion strength, and thermo-mechanical properties of WPS-based adhesives were examined to investigate the change of thermoplastic WPS to thermosetting adhesives. The bonding strength of WPS-based adhesives was evaluated in particleboard made of sengon (Falcataria moluccana (Miq.) Barneby & J.W. Grimes) wood and rice straw particles at different weight ratios according to the Japanese Industrial Standard (JIS) A 5908:2003. Rheology and Dynamic Mechanical Analysis revealed that modification with MDI and MA resulted in thermosetting properties in WPS-based adhesives by increasing the viscosity at a temperature above 72.7 °C and reaching the maximum storage modulus above 90.8 °C. WPS modified with MDI had a lower activation energy (Ea) value (83.4 kJ/mole) compared to the WPS modified with MA (150.8 kJ/mole), indicating the cross-linking with MDI was much faster compared with MA. Particleboard fabricated from 100% sengon wood particles bonded with WPS modified with MDI fulfilled the minimum requirement of JIS A 5908:2003 for interior applications.
Schlagwörter
Stichwörter der Autor:innen
Autor:innen und Institutionen
- School of Life Sciences and Technology, Institut Teknologi Bandung, Bandung 40132, Indonesia.
- Research Center for Biomass and Bioproducts, National Research and Innovation Agency, Cibinong 16911, Indonesia.
- Faculty of Forest Industry, University of Forestry, 1797 Sofia, Bulgaria.
- Department of Wood Industry, Faculty of Applied Sciences, Universiti Teknologi MARA, Cawangan Pahang Kampus Jengka, Bandar Tun Razak 26400, Malaysia.
ORCID-Profile: Tati Karliati, Muhammad Adly Rahandi Lubis, Petar Antov, Seng Hua Lee
Förderung
- Bandung Institute of Technology
- Research, Community Service and innovation program (PPMI) collaborative scheme, School of Life Sciences and Technology, Institut Teknologi Bandung
Zitieren
APA
Karliati, T., Lubis, M. A. R., Dungani, R., Maulani, R. R., Hadiyane, A., Rumidatul, A., Antov, P., Savov, V., & Lee, S. H. (2024). Performance of Particleboard Made of Agroforestry Residues Bonded with Thermosetting Adhesive Derived from Waste Styrofoam. Polymers, 16(4), 543. https://doi.org/10.3390/polym16040543
Vancouver
Karliati T, Lubis MAR, Dungani R, Maulani RR, Hadiyane A, Rumidatul A, et al. Performance of Particleboard Made of Agroforestry Residues Bonded with Thermosetting Adhesive Derived from Waste Styrofoam. Polymers. 2024;16(4):543. doi:10.3390/polym16040543
BibTeX
@article{Karliati2024,
author = {Karliati, Tati and Lubis, Muhammad Adly Rahandi and Dungani, Rudi and Maulani, Rijanti Rahaju and Hadiyane, Anne and Rumidatul, Alfi and Antov, Petar and Savov, Viktor and Lee, Seng Hua},
title = {Performance of Particleboard Made of Agroforestry Residues Bonded with Thermosetting Adhesive Derived from Waste Styrofoam},
journal = {Polymers},
year = {2024},
volume = {16},
number = {4},
pages = {543},
doi = {10.3390/polym16040543}
}
EUVIMED