EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Direct Pellet Three-Dimensional Printing of Polybutylene Adipate-co-Terephthalate for a Greener Future

Armin Karimi iD, Davood Rahmatabadi iD, Mostafa Baghani iD

Polymers · 18.01.2024 · 16 (2) · 267

DOI: 10.3390/polym16020267 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Polymers, online erschienen am 18.01.2024. Verfasst von Armin Karimi und 2 weiteren Autor:innen. Beteiligte Einrichtung: School of Mechanical Engineering, College of Engineering, University of Tehran, Tehran P.O. Box 11155-9567, Iran. Die Arbeit wurde bisher 83-mal zitiert (Crossref) und nennt 48 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

The widespread use of conventional plastics in various industries has resulted in increased oil consumption and environmental pollution. To address these issues, a combination of plastic recycling and the use of biodegradable plastics is essential. Among biodegradable polymers, poly butylene adipate-co-terephthalate (PBAT) has attracted significant attention due to its favorable mechanical properties and biodegradability. In this study, we investigated the potential of using PBAT for direct pellet printing, eliminating the need for filament conversion. To determine the optimal printing temperature, three sets of tensile specimens were 3D-printed at varying nozzle temperatures, and their mechanical properties and microstructure were analyzed. Additionally, dynamic mechanical thermal analysis (DMTA) was conducted to evaluate the thermal behavior of the printed PBAT. Furthermore, we designed and printed two structures with different infill percentages (40% and 60%) to assess their compressive strength and energy absorption properties. DMTA revealed that PBAT’s glass–rubber transition temperature is approximately −25 °C. Our findings demonstrate that increasing the nozzle temperature enhances the mechanical properties of PBAT. Notably, the highest nozzle temperature of 200 °C yielded remarkable results, with an elongation of 1379% and a tensile strength of 7.5 MPa. Moreover, specimens with a 60% infill density exhibited superior compressive strength (1338 KPa) and energy absorption compared with those with 40% infill density (1306 KPa). The SEM images showed that with an increase in the nozzle temperature, the quality of the print was greatly improved, and it was difficult to find microholes or even a layered structure for the sample printed at 200 °C.

Schlagwörter

Stichwörter der Autor:innen

3D printingPBATbiodegradable plasticsmaterial extrusionmechanical propertiesnozzle temperature

Autor:innen und Institutionen

  • School of Mechanical Engineering, College of Engineering, University of Tehran, Tehran P.O. Box 11155-9567, Iran.
  • Department of Aerospace Engineering, Sharif University of Technology, Tehran P.O. Box 11155-9567, Iran.

ORCID-Profile: Armin Karimi, Davood Rahmatabadi, Mostafa Baghani

Zitieren

APA

Karimi, A., Rahmatabadi, D., & Baghani, M. (2024). Direct Pellet Three-Dimensional Printing of Polybutylene Adipate-co-Terephthalate for a Greener Future. Polymers, 16(2), 267. https://doi.org/10.3390/polym16020267

Vancouver

Karimi A, Rahmatabadi D, Baghani M. Direct Pellet Three-Dimensional Printing of Polybutylene Adipate-co-Terephthalate for a Greener Future. Polymers. 2024;16(2):267. doi:10.3390/polym16020267

BibTeX
@article{Karimi2024,
  author = {Karimi, Armin and Rahmatabadi, Davood and Baghani, Mostafa},
  title = {Direct Pellet Three-Dimensional Printing of Polybutylene Adipate-co-Terephthalate for a Greener Future},
  journal = {Polymers},
  year = {2024},
  volume = {16},
  number = {2},
  pages = {267},
  doi = {10.3390/polym16020267}
}
Kostenlos starten →