EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Experimental Study on Warpage Phenomenon of Wax Parts Manufactured by Fused Filament Fabrication

Muslim Mukhtarkhanov, Essam Shehab iD, Md Hazrat Ali

Polymers · 11.01.2024 · 16 (2) · 208

DOI: 10.3390/polym16020208 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Polymers, online erschienen am 11.01.2024. Verfasst von Muslim Mukhtarkhanov und 2 weiteren Autor:innen. Beteiligte Einrichtung: Department of Mechanical and Aerospace Engineering, SEDS, Nazarbayev University, Astana 010000, Kazakhstan. Die Arbeit wurde bisher 13-mal zitiert (Crossref) und nennt 27 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Nazarbayev University, Ministry of Education and Science (MES), Republic of Kazakhstan.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Warpage is one of the prominent issues in Fused Filament Fabrication. The cause of this is the rapid cooling of the polymer during extrusion. The residual thermal stresses accumulated within the print part result in a shape distortion and subsequent detachment of the object from the print bed. In this study, both experimental and numerical approaches were used to identify the stresses due to thermal shrinking that occurs in soft polymers such as wax. A temperature sweep test was performed using a rotational rheometer to measure the magnitude of axial forces that are generated due to the thermal shrinking of a thin layer of 3D printable wax. The thermal stresses responsible for warpage were computed analytically and using the FEA. It was found that due to thermal processes, the stress magnitude can reach a value of 1.17 MPa. This value is enough to cause the plastic deformation in the wax part having a thin elongated shape. In addition, Taguchi’s robust design has identified two major FFF parameters that impact the warpage in amorphous soft polymers. They are the printing speed and the print bed temperature. To achieve a low level of warpage, it is important to make sure that the layer deposition occurs at medium speeds and the print bed temperature is moderately high according to the findings of this study.

Schlagwörter

Stichwörter der Autor:innen

FFFrheometerwarpagewax

Autor:innen und Institutionen

  • Department of Mechanical and Aerospace Engineering, SEDS, Nazarbayev University, Astana 010000, Kazakhstan.

ORCID-Profile: Essam Shehab

Förderung

  • Nazarbayev University
  • Ministry of Education and Science (MES), Republic of Kazakhstan

Zitieren

APA

Mukhtarkhanov, M., Shehab, E., & Ali, M. H. (2024). Experimental Study on Warpage Phenomenon of Wax Parts Manufactured by Fused Filament Fabrication. Polymers, 16(2), 208. https://doi.org/10.3390/polym16020208

Vancouver

Mukhtarkhanov M, Shehab E, Ali MH. Experimental Study on Warpage Phenomenon of Wax Parts Manufactured by Fused Filament Fabrication. Polymers. 2024;16(2):208. doi:10.3390/polym16020208

BibTeX
@article{Mukhtarkhanov2024,
  author = {Mukhtarkhanov, Muslim and Shehab, Essam and Ali, Md Hazrat},
  title = {Experimental Study on Warpage Phenomenon of Wax Parts Manufactured by Fused Filament Fabrication},
  journal = {Polymers},
  year = {2024},
  volume = {16},
  number = {2},
  pages = {208},
  doi = {10.3390/polym16020208}
}
Kostenlos starten →