EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Influence of Catalyst Content and Epoxy/Carboxylate Ratio on Isothermal Creep of Epoxy Vitrimers

Barbara Palmieri iD, Fabrizia Cilento iD, Eugenio Amendola iD, Teodoro Valente, Stefania Dello Iacono iD, Michele Giordano, Alfonso Martone iD

Polymers · 21.09.2023 · 15 (18) · 3845

DOI: 10.3390/polym15183845 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Polymers, online erschienen am 21.09.2023. Verfasst von Barbara Palmieri und 6 weiteren Autor:innen. Beteiligte Einrichtung: Institute of Polymers, Composite and Biomaterials (IPCB), National Research Council of Italy, 80055 Portici, Italy. Die Arbeit wurde bisher 19-mal zitiert (Crossref) und nennt 54 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Ministry of Economic Development.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

In the present work, a commercial epoxy based on epoxy anhydride and tertiary amine was modified by a metallic catalyst (Zn2+) to induce vitrimeric behavior by promoting the transesterification reaction. The effect of two different epoxy/acid ratios (1 and 0.6) at two different zinc acetate amounts (Zn(Ac)2) on the thermomechanical and viscoelastic performances of the epoxy vitrimers were investigated. Creep experiments showed an increase in molecular mobility above the critical “Vitrimeric” temperature (Tv) of 170 °C proportionally to the amount of Zn(Ac)2. A procedure based on Burger’s model was set up to investigate the effect of catalyst content on the vitrimer ability to flow as the effect of the dynamic exchange reaction. The analysis showed that in the case of a balanced epoxy/acid formulation, the amount of catalyst needed for promoting molecular mobility is 5%. This system showed a value of elastic modulus and dynamic viscosity at 170 °C of 9.50 MPa and 2.23 GPas, respectively. The material was easily thermoformed in compression molding, paving the way for the recyclability and weldability of the thermoset system.

Schlagwörter

Stichwörter der Autor:innen

compression moldingepoxy matrixmultifunctional compositesvitrimer

Autor:innen und Institutionen

  • Institute of Polymers, Composite and Biomaterials (IPCB), National Research Council of Italy, 80055 Portici, Italy.
  • Agenzia Spaziale Italiana (ASI), Via del Politecnico snc, 00133 Roma, Italy.

ORCID-Profile: Barbara Palmieri, Fabrizia Cilento, Eugenio Amendola, Stefania Dello Iacono, Alfonso Martone

Förderung

  • Ministry of Economic Development

Zitieren

APA

Palmieri, B., Cilento, F., Amendola, E., Valente, T., Dello Iacono, S., Giordano, M., & Martone, A. (2023). Influence of Catalyst Content and Epoxy/Carboxylate Ratio on Isothermal Creep of Epoxy Vitrimers. Polymers, 15(18), 3845. https://doi.org/10.3390/polym15183845

Vancouver

Palmieri B, Cilento F, Amendola E, Valente T, Dello Iacono S, Giordano M, et al. Influence of Catalyst Content and Epoxy/Carboxylate Ratio on Isothermal Creep of Epoxy Vitrimers. Polymers. 2023;15(18):3845. doi:10.3390/polym15183845

BibTeX
@article{Palmieri2023,
  author = {Palmieri, Barbara and Cilento, Fabrizia and Amendola, Eugenio and Valente, Teodoro and Dello Iacono, Stefania and Giordano, Michele and Martone, Alfonso},
  title = {Influence of Catalyst Content and Epoxy/Carboxylate Ratio on Isothermal Creep of Epoxy Vitrimers},
  journal = {Polymers},
  year = {2023},
  volume = {15},
  number = {18},
  pages = {3845},
  doi = {10.3390/polym15183845}
}
Kostenlos starten →