Development of Biodegradable Thermosetting Plastic Using Dialdehyde Pineapple Stem Starch
Polymers · 20.09.2023 · 15 (18) · 3832
DOI: 10.3390/polym15183832 ↗Kurz gefasst
Fachartikel in der Zeitschrift Polymers, online erschienen am 20.09.2023. Verfasst von Wasan Tessanan und 2 weiteren Autor:innen. Beteiligte Einrichtung: Department of Chemistry, Faculty of Science, Mahidol University, Rama VI Road, Payathai, Bangkok 10400, Thailand. Die Arbeit wurde bisher 11-mal zitiert (Crossref) und nennt 79 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Mahidol University.
Abstract (Originalsprache)
Starch extracted from pineapple stem waste underwent an environmentally friendly modification process characterized by low-energy consumption. This process resulted in the creation of dialdehyde pineapple stem starch featuring varying aldehyde contents ranging from 10% to 90%. Leveraging these dialdehyde starches, thermosetting plastics were meticulously developed by incorporating glycerol as a plasticizer. Concurrently, unmodified pineapple stem starch was employed as a control to produce thermoplastic material under identical conditions. The objective of streamlining the processing steps was pursued by adopting a direct hot compression molding technique. This enabled the transformation of starch powders into plastic sheets without the need for water-based gelatinization. Consequently, the dialdehyde starch-based thermosetting plastics exhibited exceptional mechanical properties, boasting a modulus within the range of 1862 MPa to 2000 MPa and a strength of 15 MPa to 42 MPa. Notably, their stretchability remained relatively modest, spanning from 0.8% to 2.4%. Comparatively, these properties significantly outperformed the thermoplastic counterpart derived from unmodified starch. Tailoring the mechanical performance of the thermosetting plastics was achieved by manipulating the glycerol content, ranging from 30% to 50%. Phase morphologies of the thermoset starch unveiled a uniformly distributed microstructure without any observable starch particles. This stood in contrast to the heterogeneous structure exhibited by the thermoplastic derived from unmodified starch. X-ray diffraction patterns indicated the absence of a crystalline structure within the thermosets, likely attributed to the establishment of a crosslinked structure. The resultant network formation in the thermosets directly correlated with enhanced water resistance. Remarkably, the thermosetting starch originating from pineapple stem starch demonstrated continued biodegradability following a soil burial test, albeit at a notably slower rate when compared to its thermoplastic counterpart. These findings hold the potential to pave the way for the utilization of starch-based products, thereby replacing non-biodegradable petroleum-based materials and contributing to the creation of more enduring and sustainable commodities.
Schlagwörter
Stichwörter der Autor:innen
Autor:innen und Institutionen
- Department of Chemistry, Faculty of Science, Mahidol University, Rama VI Road, Payathai, Bangkok 10400, Thailand.
- Center of Sustainable Energy and Green Materials, Faculty of Science, Mahidol University, Phuttamonthon 4 Road, Salaya, Nakhon Pathom 73170, Thailand.
ORCID-Profile: Taweechai Amornsakchai
Förderung
- Mahidol University
Zitieren
APA
Tessanan, W., Phinyocheep, P., & Amornsakchai, T. (2023). Development of Biodegradable Thermosetting Plastic Using Dialdehyde Pineapple Stem Starch. Polymers, 15(18), 3832. https://doi.org/10.3390/polym15183832
Vancouver
Tessanan W, Phinyocheep P, Amornsakchai T. Development of Biodegradable Thermosetting Plastic Using Dialdehyde Pineapple Stem Starch. Polymers. 2023;15(18):3832. doi:10.3390/polym15183832
BibTeX
@article{Tessanan2023,
author = {Tessanan, Wasan and Phinyocheep, Pranee and Amornsakchai, Taweechai},
title = {Development of Biodegradable Thermosetting Plastic Using Dialdehyde Pineapple Stem Starch},
journal = {Polymers},
year = {2023},
volume = {15},
number = {18},
pages = {3832},
doi = {10.3390/polym15183832}
}
EUVIMED