EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Foaming Properties of Lignosulfonates in the Flotation Process

Jhon Chique, Lina Uribe, Marek Pawlik, Andres Ramirez iD, Leopoldo Gutierrez iD

Polymers · 28.08.2023 · 15 (17) · 3575

DOI: 10.3390/polym15173575 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Polymers, online erschienen am 28.08.2023. Verfasst von Jhon Chique und 4 weiteren Autor:innen. Beteiligte Einrichtung: Department of Metallurgical Engineering, University of Concepcion, Concepción 4040371, Chile. Die Arbeit wurde bisher 5-mal zitiert (Crossref) und nennt 40 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: agencia nacional de investigación y desarrollo, Water Research Centre for Agriculture and Mining (CRHIAM) of the Universidad de Concepcion sponsored.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

The widely used technology for the selective flotation of copper and molybdenite using sodium hydrosulfide (NaSH) to depress copper sulfides creates environmental issues related to the potential emissions of toxic hydrosulfide gas (H2S) and bad odors. Previous studies showed that molybdenite flotation can be depressed by the action of lignosulfonates, but no significant progress has been made in studying the effect that these reagents have on the foaming/frothing phenomena in flotation. The objective of this work was to investigate the foaming properties of three samples of lignosulfonates through measurements of surface tension, foamability, bubble size distributions, and water recovery. A sugared sodium lignosulfonate (NaLS), a calcium lignosulfonate (CaLS), and a sample prepared by sulphomethylation of kraft lignin (KLS) were tested. It was found that all lignosulfonates displayed surface activity that decreased with pH and was related to the degree of anionicity and molecular weight. The NaLS lignosulfonate showed the highest dynamic foamability index (DFI) value, compared to that of the CaLS and KLS samples. The lignosulfonates tested in this study strongly affected bubble size. Water recovery tests performed using flotation experiments in a two-phase system showed that the KLS and NaLS samples had the strongest effect, which correlated with the surface tension, foamability, and bubble size results.

Schlagwörter

Stichwörter der Autor:innen

flotationfoamfrothlignosulfonates

Autor:innen und Institutionen

  • Department of Metallurgical Engineering, University of Concepcion, Concepción 4040371, Chile.
  • Water Research Center for Agriculture and Mining (CRHIAM), University of Concepcion, Concepción 4040371, Chile.
  • Department of Mining Engineering, University of Talca, Talca 3480094, Chile.
  • N.B. Keevil Institute of Mining Engineering, University of British Columbia, Vancouver, BC V6T 1Z4, Canada.

ORCID-Profile: Andres Ramirez, Leopoldo Gutierrez

Förderung

  • agencia nacional de investigación y desarrollo
  • Water Research Centre for Agriculture and Mining (CRHIAM) of the Universidad de Concepcion sponsored

Zitieren

APA

Chique, J., Uribe, L., Pawlik, M., Ramirez, A., & Gutierrez, L. (2023). Foaming Properties of Lignosulfonates in the Flotation Process. Polymers, 15(17), 3575. https://doi.org/10.3390/polym15173575

Vancouver

Chique J, Uribe L, Pawlik M, Ramirez A, Gutierrez L. Foaming Properties of Lignosulfonates in the Flotation Process. Polymers. 2023;15(17):3575. doi:10.3390/polym15173575

BibTeX
@article{Chique2023,
  author = {Chique, Jhon and Uribe, Lina and Pawlik, Marek and Ramirez, Andres and Gutierrez, Leopoldo},
  title = {Foaming Properties of Lignosulfonates in the Flotation Process},
  journal = {Polymers},
  year = {2023},
  volume = {15},
  number = {17},
  pages = {3575},
  doi = {10.3390/polym15173575}
}
Kostenlos starten →