EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Effect of Reinforcement with Short Carbon Fibers on the Friction and Wear Resistance of Additively Manufactured PA12

Abdelrasoul Gadelmoula iD, Saleh Ahmed Aldahash iD

Polymers · 27.07.2023 · 15 (15) · 3187

DOI: 10.3390/polym15153187 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Polymers, online erschienen am 27.07.2023. Verfasst von Abdelrasoul Gadelmoula und 1 weiteren Autor:innen. Beteiligte Einrichtung: Department of Mechanical and Industrial Engineering, College of Engineering, Majmaah University, Al-Majmaah 11952, Saudi Arabia. Die Arbeit wurde bisher 16-mal zitiert (Crossref) und nennt 30 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Deanship of Scientific Research at Majmaah University.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Reinforcing thermoplastic materials for additive manufacturing with either short, long, and continuous fibers or micro/nanoparticles is a sound means to enhance the mechanical/tribological properties of functional 3D printed objects. However, despite the fact that reinforced thermoplastics are being used extensively in modern applications, little data are found in open literature regarding the effect of such reinforcements on the friction and wear characteristics of additively manufactured objects. Therefore, this article presents a comparative study that aims to investigate the friction and wear behavior of carbon fiber-reinforced polyamide 12 (CF-PA12) as compared to pure polyamide 12 (PA12). The test specimens were prepared by selective laser sintering (SLS) at five different build orientations and examined using a pin-on-disc tribometer in dry sliding mode. The coefficient of friction (COF), interface temperature, friction-induced noise, and specific wear rate were measured. Scanning electron microscopy (SEM) was used to inspect the tribo-surfaces. The results revealed that both the COF and contact temperature of CF-PA12 are orientation-independent and are lower than those of pure PA12. Also, it was found that, compared with pure PA12, CF-PA12 has 25% smaller COF and 15–40% higher wear resistance. Further, the SEM of tribo-surfaces showed that adhesive wear dominates the surface of pure PA12, while both adhesive and abrasive wear patterns coexist in CF-PA12. Moreover, fiber crushing and thinning were observed, and this, under some circumstances, can result in a considerable increase in frictional noise.

Schlagwörter

Stichwörter der Autor:innen

carbon fiberfriction and wearfrictional noisepolyamide 12selective laser sintering

Autor:innen und Institutionen

  • Department of Mechanical and Industrial Engineering, College of Engineering, Majmaah University, Al-Majmaah 11952, Saudi Arabia.
  • Department of Mechanical Design and Production Engineering, Faculty of Engineering, Assiut University, Assiut 71515, Egypt.

ORCID-Profile: Abdelrasoul Gadelmoula, Saleh Ahmed Aldahash

Förderung

  • Deanship of Scientific Research at Majmaah University

Zitieren

APA

Gadelmoula, A., & Aldahash, S. A. (2023). Effect of Reinforcement with Short Carbon Fibers on the Friction and Wear Resistance of Additively Manufactured PA12. Polymers, 15(15), 3187. https://doi.org/10.3390/polym15153187

Vancouver

Gadelmoula A, Aldahash SA. Effect of Reinforcement with Short Carbon Fibers on the Friction and Wear Resistance of Additively Manufactured PA12. Polymers. 2023;15(15):3187. doi:10.3390/polym15153187

BibTeX
@article{Gadelmoula2023,
  author = {Gadelmoula, Abdelrasoul and Aldahash, Saleh Ahmed},
  title = {Effect of Reinforcement with Short Carbon Fibers on the Friction and Wear Resistance of Additively Manufactured PA12},
  journal = {Polymers},
  year = {2023},
  volume = {15},
  number = {15},
  pages = {3187},
  doi = {10.3390/polym15153187}
}
Kostenlos starten →