EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Integrating Exposure Assessment and Process Hazard Analysis: The Nano-Enabled 3D Printing Filament Extrusion Case

Stratos Saliakas iD, Spyridon Damilos iD, Melpo Karamitrou iD, Aikaterini-Flora Trompeta iD, Tatjana Kosanovic Milickovic iD, Costas Charitidis iD, Elias P Koumoulos iD

Polymers · 27.06.2023 · 15 (13) · 2836

DOI: 10.3390/polym15132836 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Polymers, online erschienen am 27.06.2023. Verfasst von Stratos Saliakas und 6 weiteren Autor:innen. Beteiligte Einrichtung: Innovation in Research & Engineering Solutions (IRES), 1780 Wemmel, Belgium. Die Arbeit wurde bisher 12-mal zitiert (Crossref) und nennt 51 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: European Commission, European Union’s Horizon 2020 Research and Innovation Programme REPAIR3D.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Nanoparticles are being used in novel applications of the thermoplastics industry, including automotive parts, the sports industry and leisure and consumer goods, which can be produced nowadays through additive manufacturing. However, there is limited information on the health and safety aspects during the production of these new materials, mainly from recycled sources. This study covers the exposure assessment to nano- and micro-size particles emitted from the nanocomposites during the production of filaments for 3D printing through a compounding and extrusion pilot line using recycled (post-industrial) thermoplastic polyurethane (TPU) and recycled polyamide 12 (PA12), which have been also upcycled through reinforcement with iron oxide nanoparticles (Fe3O4 NPs), introducing matrix healing properties triggered by induction heating. The assessment protocol included near- and far-field measurements, considering the extruder as the primary emission source, and portable measuring devices for evaluating particulate emissions reaching the inhalable zone of the lab workers. A Failure Modes and Effects Analysis (FMEA) study for the extrusion process line was defined along with a Failure Tree Analysis (FTA) process in which the process deviations, their sources and the relations between them were documented. FTA allowed the identification of events that should take place in parallel (simultaneously) or in series for the failure modes to take place and the respective corrective actions to be proposed (additional to the existing control measures).

Schlagwörter

Stichwörter der Autor:innen

exposure assessmentnanocompositesoccupational safetypolymer extrusion

Autor:innen und Institutionen

  • Innovation in Research & Engineering Solutions (IRES), 1780 Wemmel, Belgium.
  • Research Lab of Advanced, Composites, Nanomaterials and Nanotechnology (R-NanoLab), School of Chemical Engineering, National Technical University of Athens, Zographos, 15780 Athens, Greece.

ORCID-Profile: Stratos Saliakas, Spyridon Damilos, Melpo Karamitrou, Aikaterini-Flora Trompeta, Tatjana Kosanovic Milickovic, Costas Charitidis, Elias P Koumoulos

Förderung

  • European Commission
  • European Union’s Horizon 2020 Research and Innovation Programme REPAIR3D

Zitieren

APA

Saliakas, S., Damilos, S., Karamitrou, M., Trompeta, A. F., Milickovic, T. K., Charitidis, C., & Koumoulos, E. P. (2023). Integrating Exposure Assessment and Process Hazard Analysis: The Nano-Enabled 3D Printing Filament Extrusion Case. Polymers, 15(13), 2836. https://doi.org/10.3390/polym15132836

Vancouver

Saliakas S, Damilos S, Karamitrou M, Trompeta AF, Milickovic TK, Charitidis C, et al. Integrating Exposure Assessment and Process Hazard Analysis: The Nano-Enabled 3D Printing Filament Extrusion Case. Polymers. 2023;15(13):2836. doi:10.3390/polym15132836

BibTeX
@article{Saliakas2023,
  author = {Saliakas, Stratos and Damilos, Spyridon and Karamitrou, Melpo and Trompeta, Aikaterini-Flora and Milickovic, Tatjana Kosanovic and Charitidis, Costas and Koumoulos, Elias P},
  title = {Integrating Exposure Assessment and Process Hazard Analysis: The Nano-Enabled 3D Printing Filament Extrusion Case},
  journal = {Polymers},
  year = {2023},
  volume = {15},
  number = {13},
  pages = {2836},
  doi = {10.3390/polym15132836}
}
Kostenlos starten →