Investigations on the Fatigue Behavior of 3D-Printed and Thermoformed Polylactic Acid Wrist–Hand Orthoses
Polymers · 19.06.2023 · 15 (12) · 2737
DOI: 10.3390/polym15122737 ↗Kurz gefasst
Fachartikel in der Zeitschrift Polymers, online erschienen am 19.06.2023. Verfasst von Diana Popescu und 4 weiteren Autor:innen. Beteiligte Einrichtung: Department of Robotics and Production Systems, Faculty of Industrial Engineering and Robotics, University Politehnica of Bucharest, 060042 Bucharest,…. Die Arbeit wurde bisher 22-mal zitiert (Crossref) und nennt 42 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Unitatea Executiva Pentru Finantarea Invatamantului Superior a Cercetarii Dezvoltarii si Inovarii, Ministry of Research, Innovation and Digitization.
Abstract (Originalsprache)
Additively manufactured wrist–hand orthoses (3DP-WHOs) offer several advantages over traditional splints and casts, but their development based on a patient’s 3D scans currently requires advanced engineering skills, while also recording long manufacturing times as they are commonly built in a vertical position. A proposed alternative involves 3D printing the orthoses as a flat model base and then thermoforming them to fit the patient’s forearm. This manufacturing approach is faster, cost-effective and allows easier integration of flexible sensors as an example. However, it is unknown whether these flat-shaped 3DP-WHOs offer similar mechanical resistance as the 3D-printed hand-shaped orthoses, with a lack of research in this area being revealed by the literature review. To evaluate the mechanical properties of 3DP-WHOs produced using the two approaches, three-point bending tests and flexural fatigue tests were conducted. The results showed that both types of orthoses had similar stiffness up to 50 N, but the vertically built orthoses failed at a maximum load of 120 N, while the thermoformed orthoses could withstand up to 300 N with no damages observed. The integrity of the thermoformed orthoses was maintained after 2000 cycles at 0.5 Hz and ±2.5 mm displacement. It was observed that the minimum force occurring during fatigue tests was approximately −95 N. After 1100–1200 cycles, it reached −110 N and remained constant. The outcomes of this study are expected to enhance the trust that hand therapists, orthopedists, and patients have in using thermoformable 3DP-WHOs.
Schlagwörter
Stichwörter der Autor:innen
Autor:innen und Institutionen
- Department of Robotics and Production Systems, Faculty of Industrial Engineering and Robotics, University Politehnica of Bucharest, 060042 Bucharest, Romania.
- Department of Strength of Materials, Faculty of Industrial Engineering and Robotics, University Politehnica of Bucharest, 060042 Bucharest, Romania.
- Department of Orthopedics, Carol Davila University of Medicine and Pharmacy, 050474 Bucharest, Romania.
- Department of Orthopedics, Colentina Clinical Hospital, 020125 Bucharest, Romania.
ORCID-Profile: Diana Popescu, Florin Baciu
Förderung
- Unitatea Executiva Pentru Finantarea Invatamantului Superior a Cercetarii Dezvoltarii si Inovarii
- Ministry of Research, Innovation and Digitization
Zitieren
APA
Popescu, D., Baciu, F., Vlăsceanu, D., Marinescu, R., & Lăptoiu, D. (2023). Investigations on the Fatigue Behavior of 3D-Printed and Thermoformed Polylactic Acid Wrist–Hand Orthoses. Polymers, 15(12), 2737. https://doi.org/10.3390/polym15122737
Vancouver
Popescu D, Baciu F, Vlăsceanu D, Marinescu R, Lăptoiu D. Investigations on the Fatigue Behavior of 3D-Printed and Thermoformed Polylactic Acid Wrist–Hand Orthoses. Polymers. 2023;15(12):2737. doi:10.3390/polym15122737
BibTeX
@article{Popescu2023,
author = {Popescu, Diana and Baciu, Florin and Vlăsceanu, Daniel and Marinescu, Rodica and Lăptoiu, Dan},
title = {Investigations on the Fatigue Behavior of 3D-Printed and Thermoformed Polylactic Acid Wrist–Hand Orthoses},
journal = {Polymers},
year = {2023},
volume = {15},
number = {12},
pages = {2737},
doi = {10.3390/polym15122737}
}
EUVIMED