From Bottle Caps to Frisbee—A Case Study on Mechanical Recycling of Plastic Waste towards a Circular Economy
Polymers · 14.06.2023 · 15 (12) · 2685
DOI: 10.3390/polym15122685 ↗Kurz gefasst
Fachartikel in der Zeitschrift Polymers, online erschienen am 14.06.2023. Verfasst von Mohamad Hassan Akhras und 3 weiteren Autor:innen. Beteiligte Einrichtung: Competence Center CHASE GmbH, Hafenstraße 47-51, 4020 Linz, Austria. Die Arbeit wurde bisher 30-mal zitiert (Crossref) und nennt 94 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Austrian Research Promotion Agency.
Abstract (Originalsprache)
This study demonstrates an open-loop recycling process of a specific post-consumer plastic waste stream. The targeted input waste material was defined as high-density polyethylene beverage bottle caps. Two methods of waste collection, informal and formal, were employed. Thereafter, materials were hand-sorted, shredded, regranulated, and then injection-molded into a flying disc (i.e., frisbee) as a pilot product. To observe the potential changes in the material throughout the entire recycling process, eight different test methods including melt mass-flow rate (MFR), differential scanning calorimetry (DSC), and mechanical tests were carried out on the various material states. The study showed that the informal collection led to a relatively higher purity in the input stream, which also appeared to have a 23% lower MFR value compared to that of the formally collected materials. The DSC measurements revealed a cross-contamination by polypropylene, which clearly affected the properties of all investigated materials. The cross-contamination led to a slightly higher tensile modulus in the recyclate, while the Charpy notched impact strength declined after processing by approximately 15% and 8% compared to those of the informal and formal input materials, respectively. All materials and the processing data were documented and stored online as a practical implementation of a digital product passport as a potential digital traceability tool. Furthermore, the suitability of the resulting recyclate to be used in transport packaging applications was also investigated. It was found that a direct replacement of virgin materials for this specific application is not possible without proper material modification.
Schlagwörter
Stichwörter der Autor:innen
Autor:innen und Institutionen
- Competence Center CHASE GmbH, Hafenstraße 47-51, 4020 Linz, Austria.
- Institute of Polymeric Materials and Testing, Johannes Kepler University, Altenberger Straße 69, 4040 Linz, Austria.
- Institute for Polymer Injection Moulding and Process Automation, Johannes Kepler University, Altenberger Straße 69, 4040 Linz, Austria.
ORCID-Profile: Mohamad Hassan Akhras, Paul J Freudenthaler, Joerg Fischer
Förderung
- Austrian Research Promotion Agency
Zitieren
APA
Akhras, M. H., Freudenthaler, P. J., Straka, K., & Fischer, J. (2023). From Bottle Caps to Frisbee—A Case Study on Mechanical Recycling of Plastic Waste towards a Circular Economy. Polymers, 15(12), 2685. https://doi.org/10.3390/polym15122685
Vancouver
Akhras MH, Freudenthaler PJ, Straka K, Fischer J. From Bottle Caps to Frisbee—A Case Study on Mechanical Recycling of Plastic Waste towards a Circular Economy. Polymers. 2023;15(12):2685. doi:10.3390/polym15122685
BibTeX
@article{Akhras2023,
author = {Akhras, Mohamad Hassan and Freudenthaler, Paul J and Straka, Klaus and Fischer, Joerg},
title = {From Bottle Caps to Frisbee—A Case Study on Mechanical Recycling of Plastic Waste towards a Circular Economy},
journal = {Polymers},
year = {2023},
volume = {15},
number = {12},
pages = {2685},
doi = {10.3390/polym15122685}
}
EUVIMED