EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Fabrication of CuO-NP-Doped PVDF Composites Based Electrospun Triboelectric Nanogenerators for Wearable and Biomedical Applications

Bindhu Amrutha, Gajula Prasad iD, Ponnan Sathiyanathan iD, Mohammad Shamim Reza, Hongdoo Kim, Madhvesh Pathak, Arun Anand Prabu iD

Polymers · 25.05.2023 · 15 (11) · 2442

DOI: 10.3390/polym15112442 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Polymers, online erschienen am 25.05.2023. Verfasst von Bindhu Amrutha und 6 weiteren Autor:innen. Beteiligte Einrichtung: Department of Chemistry, School of Advanced Sciences, Vellore Institute of Technology, Vellore 632014, India. Die Arbeit wurde bisher 46-mal zitiert (Crossref) und nennt 101 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: MHRD-SPARC India, MHRD-SPARC, India.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

A flexible and portable triboelectric nanogenerator (TENG) based on electrospun polyvinylidene fluoride (PVDF) doped with copper oxide (CuO) nanoparticles (NPs, 2, 4, 6, 8, and 10 wt.-% w.r.t. PVDF content) was fabricated. The structural and crystalline properties of the as-prepared PVDF-CuO composite membranes were characterized using SEM, FTIR, and XRD. To fabricate the TENG device, the PVDF-CuO was considered a tribo-negative film and the polyurethane (PU) a counter-positive film. The output voltage of the TENG was analyzed using a custom-made dynamic pressure setup, under a constant load of 1.0 kgf and 1.0 Hz frequency. The neat PVDF/PU showed only 1.7 V, which further increased up to 7.5 V when increasing the CuO contents from 2 to 8 wt.-%. A decrease in output voltage to 3.9 V was observed for 10 wt.-% CuO. Based on the above results, further measurements were carried out using the optimal sample (8 wt.-% CuO). Its output voltage performance was evaluated as a function of varying load (1 to 3 kgf) and frequency (0.1 to 1.0 Hz) conditions. Finally, the optimized device was demonstrated in real-time wearable sensor applications, such as human motion and health-monitoring applications (respiration and heart rate).

Schlagwörter

Stichwörter der Autor:innen

CuOPVDFelectrospinninghealth monitoringtriboelectric nanogenerator

Autor:innen und Institutionen

  • Department of Chemistry, School of Advanced Sciences, Vellore Institute of Technology, Vellore 632014, India.
  • School of Energy, Materials and Chemical Engineering, Korea University of Technology and Education, 1600, Cheonan-si 31253, Chungcheongnam-do, Republic of Korea.
  • Department of Advanced Materials Engineering for Information & Electronics, College of Engineering, Kyung Hee University, Yongin-si 17104, Gyeonggi-do, Republic of Korea.

ORCID-Profile: Gajula Prasad, Ponnan Sathiyanathan, Arun Anand Prabu

Förderung

  • MHRD-SPARC India
  • MHRD-SPARC, India

Zitieren

APA

Amrutha, B., Prasad, G., Sathiyanathan, P., Reza, M. S., Kim, H., Pathak, M., & Prabu, A. A. (2023). Fabrication of CuO-NP-Doped PVDF Composites Based Electrospun Triboelectric Nanogenerators for Wearable and Biomedical Applications. Polymers, 15(11), 2442. https://doi.org/10.3390/polym15112442

Vancouver

Amrutha B, Prasad G, Sathiyanathan P, Reza MS, Kim H, Pathak M, et al. Fabrication of CuO-NP-Doped PVDF Composites Based Electrospun Triboelectric Nanogenerators for Wearable and Biomedical Applications. Polymers. 2023;15(11):2442. doi:10.3390/polym15112442

BibTeX
@article{Amrutha2023,
  author = {Amrutha, Bindhu and Prasad, Gajula and Sathiyanathan, Ponnan and Reza, Mohammad Shamim and Kim, Hongdoo and Pathak, Madhvesh and Prabu, Arun Anand},
  title = {Fabrication of CuO-NP-Doped PVDF Composites Based Electrospun Triboelectric Nanogenerators for Wearable and Biomedical Applications},
  journal = {Polymers},
  year = {2023},
  volume = {15},
  number = {11},
  pages = {2442},
  doi = {10.3390/polym15112442}
}
Kostenlos starten →