EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Thermoplastic Pultrusion Process of Polypropylene/Glass Tapes

Fausto Tucci iD, Felice Rubino iD, Germana Pasquino, Pierpaolo Carlone iD

Polymers · 19.05.2023 · 15 (10) · 2374

DOI: 10.3390/polym15102374 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Polymers, online erschienen am 19.05.2023. Verfasst von Fausto Tucci und 3 weiteren Autor:innen. Beteiligte Einrichtung: Department of Industrial Engineering, University of Salerno, 84084 Fisciano, Italy. Die Arbeit wurde bisher 24-mal zitiert (Crossref) und nennt 29 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

The present work focuses on the pultrusion of pre-impregnated glass-reinforced polypropylene tapes. An appositely designed laboratory-scale pultrusion line, consisting of a heating/forming die and a cooling die, was used. The temperature of the advancing materials and the pulling force resistance were measured by using thermocouples embedded in the pre-preg tapes and a load cell. From the analysis of the experimental outcomes, we gained insight into the nature of the material–machinery interaction and the transitions of the polypropylene matrix. The cross-section of the pultruded part was analyzed by microscope observation to evaluate the distribution of the reinforcement inside the profile and the presence of internal defects. Three-point bending and tensile testing were conducted to assess the mechanical properties of the thermoplastic composite. The pultruded product showed good quality, with an average fiber volume fraction of 23% and a limited presence of internal defects. A non-homogenous distribution of fibers in the cross-section of the profile was observed, probably due to the low number of tapes used in the present experimentation and their limited compaction. A tensile modulus and a flexural modulus of 21.5 GPa and 15.0 GPa, respectively, were measured.

Schlagwörter

Stichwörter der Autor:innen

compositeglasspolypropylenepre-impregnatedpultrusiontapestestingthermoplastic

Autor:innen und Institutionen

  • Department of Industrial Engineering, University of Salerno, 84084 Fisciano, Italy.
  • Department of Civil and Mechanical Engineering, University of Cassino and Southern Lazio, 03043 Cassino, Italy.
  • Universitas Mercatorum, 00186 Rome, Italy.

ORCID-Profile: Fausto Tucci, Felice Rubino, Pierpaolo Carlone

Zitieren

APA

Tucci, F., Rubino, F., Pasquino, G., & Carlone, P. (2023). Thermoplastic Pultrusion Process of Polypropylene/Glass Tapes. Polymers, 15(10), 2374. https://doi.org/10.3390/polym15102374

Vancouver

Tucci F, Rubino F, Pasquino G, Carlone P. Thermoplastic Pultrusion Process of Polypropylene/Glass Tapes. Polymers. 2023;15(10):2374. doi:10.3390/polym15102374

BibTeX
@article{Tucci2023,
  author = {Tucci, Fausto and Rubino, Felice and Pasquino, Germana and Carlone, Pierpaolo},
  title = {Thermoplastic Pultrusion Process of Polypropylene/Glass Tapes},
  journal = {Polymers},
  year = {2023},
  volume = {15},
  number = {10},
  pages = {2374},
  doi = {10.3390/polym15102374}
}
Kostenlos starten →