EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Effect of 3D Printing Process Parameters and Heat Treatment Conditions on the Mechanical Properties and Microstructure of PEEK Parts

Honglei Zhen, Bin Zhao, Long Quan, Junyu Fu

Polymers · 06.05.2023 · 15 (9) · 2209

DOI: 10.3390/polym15092209 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Polymers, online erschienen am 06.05.2023. Verfasst von Honglei Zhen und 3 weiteren Autor:innen. Beteiligte Einrichtung: College of Mechanical and Vehicle Engineering, Taiyuan University of Technology, Taiyuan 030024, China. Die Arbeit wurde bisher 69-mal zitiert (Crossref) und nennt 40 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Fused deposition modeling (FDM) processed Poly-ether-ether-ketone (PEEK) materials are widely used in aerospace, automobile, biomedical, and electronics industries and other industries due to their excellent mechanical properties, thermal properties, chemical resistance, wear resistance, and biocompatibility, etc. However, the manufacture of PEEK materials and parts utilizing the FDM process faces the challenge of fine-tuning a list of process parameters and heat treatment conditions to reach the best-suiting mechanical properties and microstructures. It is non-trivial to make the selection only according to theoretical analysis while counting on a vast number of experiments is the general situation. Therefore, in this paper, the extrusion rate, filling angle, and printing orientation are investigated to adjust the mechanical properties of 3D-printed PEEK parts; then, a variety of heat treatment conditions were applied to tune the crystallinity and strength. The results show that the best mechanical performance is achieved at 1.0 times the extrusion rate, varied angle cross-fillings with ±10° intervals, and vertical printing. Horizontal printing performs better with reduced warpage. Additionally, both crystallinity and mechanical properties are significantly improved after heat treatment, and the best state is achieved after holding at 300 °C for 2 h. The resulting tensile strength is close to 80% of the strength of injection-molded PEEK parts.

Schlagwörter

Stichwörter der Autor:innen

3D printingheat treatmentmechanical propertiespoly-ether-ether-ketone (PEEK)printing parameters

Autor:innen und Institutionen

  • College of Mechanical and Vehicle Engineering, Taiyuan University of Technology, Taiyuan 030024, China.

Zitieren

APA

Zhen, H., Zhao, B., Quan, L., & Fu, J. (2023). Effect of 3D Printing Process Parameters and Heat Treatment Conditions on the Mechanical Properties and Microstructure of PEEK Parts. Polymers, 15(9), 2209. https://doi.org/10.3390/polym15092209

Vancouver

Zhen H, Zhao B, Quan L, Fu J. Effect of 3D Printing Process Parameters and Heat Treatment Conditions on the Mechanical Properties and Microstructure of PEEK Parts. Polymers. 2023;15(9):2209. doi:10.3390/polym15092209

BibTeX
@article{Zhen2023,
  author = {Zhen, Honglei and Zhao, Bin and Quan, Long and Fu, Junyu},
  title = {Effect of 3D Printing Process Parameters and Heat Treatment Conditions on the Mechanical Properties and Microstructure of PEEK Parts},
  journal = {Polymers},
  year = {2023},
  volume = {15},
  number = {9},
  pages = {2209},
  doi = {10.3390/polym15092209}
}
Kostenlos starten →