EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Effect of UV-C Radiation on 3D Printed ABS-PC Polymers

Catalin Gheorghe Amza iD, Aurelian Zapciu iD, Florin Baciu iD, Constantin Radu

Polymers · 21.04.2023 · 15 (8) · 1966

DOI: 10.3390/polym15081966 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Polymers, online erschienen am 21.04.2023. Verfasst von Catalin Gheorghe Amza und 3 weiteren Autor:innen. Beteiligte Einrichtung: Faculty of Industrial Engineering and Robotics, University Politehnica of Bucharest, 060042 Bucharest, Romania. Die Arbeit wurde bisher 36-mal zitiert (Crossref) und nennt 95 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

During the initial stages of the COVID-19 pandemic, healthcare facilities experienced severe shortages of personal protective equipment (PPE) and other medical supplies. Employing 3D printing to rapidly fabricate functional parts and equipment was one of the emergency solutions used to tackle these shortages. Using ultraviolet light in the UV-C band (wavelengths of 200 nm to 280 nm) might prove useful in sterilizing 3D printed parts, enabling their reusability. Most polymers, however, degrade under UV-C radiation, so it becomes necessary to determine what 3D printing materials can withstand the conditions found during medical equipment sterilization with UV-C. This paper analyzes the effect of accelerated aging through prolonged exposure to UV-C on the mechanical properties of parts 3D printed from a polycarbonate and acrylonitrile butadiene styrene polymer (ABS-PC). Samples 3D printed using a material extrusion process (MEX) went through a 24-h UV-C exposure aging cycle and then were tested versus a control group for changes in tensile strength, compressive strength and some selected material creep characteristics. Testing showed minimal mechanical property degradation following the irradiation procedure, with tensile strength being statistically the same for irradiated parts as those in the control group. Irradiated parts showed small losses in stiffness (5.2%) and compressive strength (6.5%). Scanning electron microscopy (SEM) was employed in order to assess if any changes occurred in the material structure.

Schlagwörter

Stichwörter der Autor:innen

3D-printing polymersABS-PCPCABSUV-Caccelerated agingultraviolet

Autor:innen und Institutionen

  • Faculty of Industrial Engineering and Robotics, University Politehnica of Bucharest, 060042 Bucharest, Romania.

ORCID-Profile: Catalin Gheorghe Amza, Aurelian Zapciu, Florin Baciu

Zitieren

APA

Amza, C. G., Zapciu, A., Baciu, F., & Radu, C. (2023). Effect of UV-C Radiation on 3D Printed ABS-PC Polymers. Polymers, 15(8), 1966. https://doi.org/10.3390/polym15081966

Vancouver

Amza CG, Zapciu A, Baciu F, Radu C. Effect of UV-C Radiation on 3D Printed ABS-PC Polymers. Polymers. 2023;15(8):1966. doi:10.3390/polym15081966

BibTeX
@article{Amza2023,
  author = {Amza, Catalin Gheorghe and Zapciu, Aurelian and Baciu, Florin and Radu, Constantin},
  title = {Effect of UV-C Radiation on 3D Printed ABS-PC Polymers},
  journal = {Polymers},
  year = {2023},
  volume = {15},
  number = {8},
  pages = {1966},
  doi = {10.3390/polym15081966}
}
Kostenlos starten →